MC68340 datasheet(81/441 Pages) FREESCALE

81 / 441 page

3- 32

MC68340 USER’S MANUAL

MOTOROLA

3.5 BUS EXCEPTION CONTROL CYCLES

The bus architecture requires assertion of

DSACK

≈ from an external device to signal that

a bus cycle is complete. Neither

DSACK

≈ nor AVEC is asserted in the following cases:

•

DSACK

≈/AVEC is programmed to respond internally.

• The external device does not respond.

• Various other application-dependent errors occur.

The MC68340 provides

BERR when no device responds by asserting DSACK

≈/AVEC

within an appropriate period of time after the MC68340 asserts

AS. This mechanism

allows the cycle to terminate and the MC68340 to enter exception processing for the error

condition.

HALT is also used for bus exception control. This signal can be asserted by an

external device for debugging purposes to cause single bus cycle operation, or, in

combination with

BERR, a retry of a bus cycle in error. To properly control termination of a

bus cycle for a retry or a bus error condition,

DSACK

≈, BERR, and HALT can be asserted

and negated with the rising edge of the MC68340 clock. This assures that when two

signals are asserted simultaneously, the required setup and hold time for both is met for

the same falling edge of the MC68340 clock. This or an equivalent precaution should be

designed into the external circuitry to provide these signals. Alternatively, the internal bus

monitor could be used. The acceptable bus cycle terminations for asynchronous cycles

are summarized in relation to

DSACK

≈ assertion as follows (case numbers refer to Table

3-4):

• Normal Termination:

DSACK

≈ is asserted; BERR and HALT remain negated (case 1).

• Halt Termination:

HALT is asserted at the same time as or before DSACKx, and

BERR remains negated (case 2).

• Bus Error Termination:

BERR is asserted in lieu of, at the same time as, or before

DSACK

≈ (case 3) or after DSACK≈ (case 4), and HALT remains negated; BERR is

negated at the same time as or after

DSACK

≈.

• Retry Termination:

HALT and BERR are asserted in lieu of, at the same time as, or

before

DSACK

≈ (case 5) or after DSACK≈ (case 6); BERR is negated at the same

time as or after

DSACK

≈, and HALT may be negated at the same time as or after

BERR.

Table 3-4 lists various combinations of control signal sequences and the resulting bus

cycle terminations. To ensure predictable operation,

BERR and HALT should be negated

according to the specifications given in Section 11 Electrical Characteristics.

DSACK

≈

BERR, and HALT may be negated after AS. If DSACK

≈ or BERR remain asserted into S2

of the next bus cycle, that cycle may be terminated prematurely.

EXAMPLE A: A system uses a bus monitor timer to terminate accesses to an unpopulated

address space. The timer asserts

BERR after timeout (case 3).

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

MC68340 bảng dữ liệu(PDF) 81 Page - Freescale Semiconductor, Inc

MC68340 bảng dữ liệu(HTML) 81 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL