ISL72027SEH

FN8763 Rev 3.00

Page 5 of 19

August 16, 2016

Absolute Maximum Ratings

Thermal Information

VCC to GND with/without Ion Beam. . . . . . . . . . . . . . . . . . . . . -0.3V to 5.5V

CANH, CANL, VREF Under Ion Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18V

CANH, CANL, VREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V

I/O Voltages

D, R, RS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V

Receiver Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . .-10mA to 10mA

Output Short-circuit Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous

ESD Rating:

Human Body Model (Tested per MIL-PRF-883 3015.7)

CANH, CANL Bus Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4kV

All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4kV

Charged Device Model (Tested per JESD22-C101D) . . . . . . . . . . . . . . 750V

Machine Model (Tested per JESD22-A115-A) . . . . . . . . . . . . . . . . . . . . 200V

Thermal Resistance (Typical)

JA (°C/W) JC (°C/W)

8 Ld FP Package (Notes 3, 4) Direct Attach .

39

7

Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+175°C

Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C

Recommended Operating Conditions

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +125°C

VCC Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3V to 3.6V

Voltage on CAN I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7V to 12V

VIH D Logic Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 5.5V

VIL D Logic Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to 0.8V

IOH Driver (CANH - CANL = 1.5V, VCC = 3.3V) . . . . . . . . . . . . . . . . . . - 40mA

IOH Receiver (VOH = 2.4V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4mA

IOL Driver (CANH - CANL = 1.5V, VCC = 3.3V) . . . . . . . . . . . . . . . . . . +40mA

IOL Receiver (VOL = 0.4V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4mA

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product

reliability and result in failures not covered by warranty.

3.

JA is measured with the component mounted on a high effective thermal conductivity test board (two buried 1oz copper planes) with “direct attach”

features package base mounted to PCB thermal land with a 10 mil gap fill material having a k of 1W/m-K. See Tech Brief TB379.

4. For

JC, the “case temp” location is the center of the package underside.

Electrical Specifications Test Conditions: VCC = 3V to 3.6V; Typicals are at TA = +25°C (Note 7); unless otherwise specified (Note 5).

Boldface limits apply across the operating temperature range, -55°C to +125°C or across a total ionizing dose of 75krad(Si) at +25°C with exposure at

a low dose rate of <10mrad(Si)/s.

PARAMETER

SYMBOL

TEST CONDITIONS

TEMP

(°C)

MIN

(Note 6)

TYP

(Note 7)

MAX

(Note 6)UNIT

DRIVER ELECTRICAL CHARACTERISTICS

Dominant Bus Output Voltage

VO(DOM)

D = 0V, CANH, RS = 0V,

Figures 10 and 11

3V

 VCC  3.6V

Full

2.25

2.85

VCC

V

D = 0V, CANL, RS = 0V,

Figures 10 and 11

Full

0.10

0.65

1.25

V

Recessive Bus Output Voltage

VO(REC)

D = 3V, CANH, RS = 0V, 60Ω



and no load, Figures 10 and

11

3V

 VCC  3.6V

Full

1.80

2.30

2.70

V

D = 3V, CANL, RS = 0V, 60Ω



and no load, Figures 10 and

11

Full

1.80

2.30

2.80

V

Dominant Output Differential

Voltage

VOD(DOM)

D = 0V, RS = 0V, 3V

VCC  3.6V, Figures 10 and 11 Full

1.5

2.2

3.0

V

D = 0V, RS = 0V, 3V

VCC  3.6V, Figures 11 and 12 Full

1.2

2.1

3.0

V

Recessive Output Differential

Voltage

VOD(REC)

D = 3V, RS = 0V, 3V

 VCC  3.6V, Figures 10 and 11 Full

-120

0.2

12

mV

D = 3V, RS = 0V, 3.0V

VCC  3.6V, no load

Full

-500

-34

50

mV

Logic Input High Voltage (D)

VIH

3V

VCC  3.6V, Note 8

Full

2.0

-

5.5

V

Logic Input Low Voltage (D)

VIL

3V

 VCC  3.6V, Note 8

Full

0

-

0.8

V

High Level Input Current (D)

IIH

D = 2V, 3V

 VCC  3.6V

Full

-30

-3

30

µA

Low Level Input Current (D)

IIL

D = 0.8V, 3V

 VCC  3.6V

Full

-30

-7

30

µA

RS Input Voltage for Listen

Mode

VIN(RS)

3V

 VCC  3.6V

Full

0.75xVCC

1.90

5.5

V