| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LT1784CS5 bảng dữ liệu(PDF) 9 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LT1784CS5 bảng dữ liệu(HTML) 9 Page - Linear Technology |
|
9 / 12 page ![]() 9 LT1784 APPLICATIO S I FOR ATIO Supply Voltage The positive supply pin of the LT1784 should be bypassed with a small capacitor (typically 0.1 µF) within an inch of the pin. When driving heavy loads, and additional 4.7 µF electrolytic capacitor should be used. When using split supplies the same is true for the negative supply pin. The LT1784 is protected against reverse battery voltages up to 18V. In the event a reverse battery condition occurs the supply current is less than 1nA. Inputs The LT1784 has two input stages, NPN and PNP (see the Simplified Schematic), resulting in three distinct operating regions as shown in the “Input Bias Current vs Common Mode” Typical Performance Characteristic Curve. For input voltages about 1V or more below V+, the PNP input stage is active and the input bias current is typically –250nA. When the input common mode voltage is within 0.6V of the positive rail, the NPN stage is operating and the input bias current is typically 500nA. Increases in tem- perature will cause the voltage at which operation switches from the PNP input stage to the NPN input stage to move towards V +. The input offset voltage of the NPN stage is untrimmed and is typically 3mV. A Schottky diode in the collector of the input transistors, along with special geometries for these NPN transistors, allow the LT1784 to operate with either or both of its inputs above V+. At about 0.3V above V+, the NPN input transis- tors is fully saturated and the input bias current is typically 200 µA at room temperature. The input offset voltage is typically 3mV when operating above V+. The LT1784 will operate with inputs 18V above V– regardless of V+. The inputs are protected against excursions as much as 10V below V– by an internal 1k resistor in series with each input and a diode from the input to the negative supply. The input stage of the LT1784 incorporates phase reversal protection to prevent the output from phase reversing for inputs up to 9V below V–. There are no clamping diodes between the inputs and the maximum differential input voltage is 18V. Output The output of the LT1784 can swing to within 80mV of the positive rail and within 4mV of the negative rail with no load. When monitoring input voltages within 80mV of the positive rail or within 4mV of the negative rail, gain should be taken to keep the output from clipping. The LT1784 can typically sink and source over 25mA at ±5V supplies, sourcing current is reduced to 7.5mA at 3V total supplies as noted in the electrical characteristics. The LT1784 is internally compensated to drive at least 400pF of capacitance under any output loading condi- tions. A 0.22 µF capacitor in series with a 150Ω resistor between the output and ground will compensate these amplifiers for larger capacitive loads, up to 10,000pF at all output currents. Distortion There are two main contributors to distortion in op amps: output crossover distortion as the output transitions from sourcing to sinking current, and distortion caused by nonlinear common mode rejection. If the op amp is operating inverting, there is no common mode induced distortion. If the op amp is operating in the PNP input stage (input not within 1V of V+), the CMRR is very good, typically 95dB. When the LT1784 switches between input stages, there is significant nonlinearity in the CMRR. Lower load resistance increases the output crossover distortion but has no effect on the input stage transition distortion. For lowest distortion, the LT1784 should be operated single supply, with the output always sourcing current and with the input voltage swing between ground and (V+ –1V). See Typical Performance Characteristics Curve, “Total Harmonic Distortion + Noise vs Output Voltage Amplitude.” Gain The open-loop gain is almost independent of load when the output is sourcing current. This optimizes perfor- mance in single supply applications where the load is returned to ground. The Typical Performance Characteric Curve “Open-Loop Gain” for various loads shows the details. |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |