ASM330LHB datasheet(20/131 Pages) STMICROELECTRONICS

20 / 131 page

5.1.1.1

I²C operation

The transaction on the bus is started through a start (ST) signal. A start condition is defined as a high to low

transition on the data line while the SCL line is held high. After this has been transmitted by the master, the bus

is considered busy. The next byte of data transmitted after the start condition contains the address of the slave in

the first 7 bits and the eighth bit tells whether the master is receiving data from the slave or transmitting data to

the slave. When an address is sent, each device in the system compares the first seven bits after a start condition

with its address. If they match, the device considers itself addressed by the master.

The slave address (SAD) associated to the ASM330LHB is 110101xb. The SDO/SA0 pin can be used to modify

the less significant bit of the device address. If the SDO/SA0 pin is connected to the supply voltage, LSb is 1

(address 1101011b); else if the SDO/SA0 pin is connected to ground, the LSb value is 0 (address 1101010b). This

solution permits to connect and address two different inertial modules to the same I²C bus.

Data transfer with acknowledge is mandatory. The transmitter must release the SDA line during the acknowledge

pulse. The receiver must then pull the data line low so that it remains stable low during the high period of the

acknowledge clock pulse. A receiver which has been addressed is obliged to generate an acknowledge after each

byte of data received.

The I²C embedded inside the ASM330LHB behaves like a slave device and the following protocol must be

adhered to. After the start condition (ST) a slave address is sent, once a slave acknowledge (SAK) has been

returned, an 8-bit subaddress (SUB) is transmitted. The increment of the address is configured by CTRL3_C

(12h) (IF_INC).

The slave address is completed with a read/write bit. If the bit is 1 (read), a repeated start (SR) condition

must be issued after the two subaddress bytes; if the bit is 0 (write) the master transmits to the slave with

direction unchanged. Table 11 explains how the SAD+read/write bit pattern is composed, listing all the possible

configurations.

Table 11. SAD+read/write patterns

Command

SAD[6:1]

SAD[0] = SA0

R/W

SAD+R/W

Read

110101

11010101 (D5h)

Write

110101

11010100 (D4h)

Read

110101

11010111 (D7h)

Write

110101

11010110 (D6h)

Table 12. Transfer when master is writing one byte to slave

Master

SAD + W

SUB

DATA

Slave

SAK

Table 13. Transfer when master is writing multiple bytes to slave

Master

SAD + W

SUB

DATA

Slave

SAK

Table 14. Transfer when master is receiving (reading) one byte of data from slave

Master

SAD + W

SUB

SAD + R

NMAK

Slave

SAK

DATA

Table 15. Transfer when master is receiving (reading) multiple bytes of data from slave

Master

SAD+W

SUB

SAD+R

MAK

NMAK

Slave

SAK

DATA

ASM330LHB

I²C/SPI interface

DS13773 - Rev 7

page 20/131

ASM330LHB bảng dữ liệu(PDF) 20 Page - STMicroelectronics

ASM330LHB bảng dữ liệu(HTML) 20 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL