No.

Item

Specifications

Test Method

Temperature

Compensating Type

High Dielectric Type

18

High

Temperature

Load

The measured and observed characteristics should satisfy the

specifications in the following table

Apply 200% of the rated voltage at the maximum operating

temperature

T3D for 1000T12 hours.

Set for 24

T2 hours (temperature compensating type)

or 48

T4 hours (high dielectric constant type) at room

temperature, then measure.

The charge/discharge current is less than 50mA.

#Initial measurement for high dielectric constant type.

Apply 200% of the rated DC voltage at the maximun operating

temperature

T3D for one hour. Remove and set for 48T4

hours at room temperature.

Perform initial measurement.

Appearance

No defects or abnormalities

Capacitance

Change

Within

T3% or T0.3pF

(Whichever is larger)

B1, B3, R1, R6, R7

: Within

T12.5%

F1, F5, E4 : Within

T30%

[Exept 10Vmax. and.

C

U1.0µF]

F1, F5 : Within

W30/Y40%

[10Vmax. and. C

U1.0µF]

Q/D.F.

30pF and over : Q

U350

10pF and over

30pF and below :

Q

U275W2.5C

10pF and below :

Q

U200W10C

C : Nominal Capacitance (pF)

[B1, B3, R1, R6, R7, E4]

W.V. : 25Vmin. : 0.04max.

W.V. : 16/10V : 0.05max.

W.V. : 6.3V

: 0.075max.(C

F3.3µF)

: 0.125max.(C

U3.3µF)

[F1, F5]

W.V. : 25Vmin.

: 0.075max.(C

F0.1µF)

: 0.125max.(C

U0.1µF)

W.V. : 16V/10V : 0.15max.

W.V. : 6.3V : 0.2max.

I.R.

More than 1,000M

Continued from the preceding page.

17

Humidity

Load

The measured and observed characteristics should satisfy the

specifications in the following table

Apply the rated voltage at 40

T2D and 90 to 95% humidity for

500

T12 hours. Remove and set for 24T2 hours (temperature

compensating type) or 48

T4 hours (high dielectric constant

type) at room temprature, then muasure. The charge/discharge

current is less than 50mA.

#Initial measurement for F1, F5/10V max.

Apply the rated DC voltage for 1 hour at 40

T2D.

Remove and set for 48

T4 hours at room temperature.

Perform initial measurement.

Appearance

No defects or abnormalities

Capacitance

Change

Within

T7.5% or T0.75pF

(Whichever is larger)

B1, B3, R1, R6, R7

: Within

T12.5%

F1, F5, E4 : Within

T30%

[W.V. : 10Vmax.]

F1, F5 : Within

W30/Y40%

Q/D.F.

30pF and over : Q

U200

30pF and below :

Q

U100W10C/3

C : Nominal Capacitance (pF)

[B1, B3, R1, R6, R7, E4]

W.V. : 25Vmin. : 0.05max.

W.V. : 16/10V : 0.05max.

W.V. : 6.3V

: 0.075max. (C

F3.3µF)

: 0.125max. (C

U3.3µF)

[F1, F5]

W.V. : 25Vmin.

: 0.075max. (C

F0.1µF)

: 0.125max. (C

U0.1µF)

W.V. : 16V/10V : 0.15max.

W.V. : 6.3V : 0.2max.

I.R.

More than 500M

Ω or 25Ω • F (Whichever is smaller)

Continued on the following page.

before ordering. Especially, please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in them to prevent smoking and/or burning, etc.

• You are able to read a detailed specification in the website (http://search.murata.co.jp/) before to require our product specification or to transact the approval sheet for product specification.

Capacitors