http://www.tracopower.com

Page 2 of 8

All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.

Battery Controller Module

TSP-BCMU360 Series

360 Watt

Output Specifications

Output voltage / current

– Normal Mode

24 VDC mode: Vin – (0.4 - 0.8V); 15 A max.

48 VDC mode: Vin – (0.4 - 0.7V); 7.5 A max.

– Buffer Mode

24 VDC mode: 22.2 – 22.9 VDC; 10 A (15 A in boost mode for 10min)

48 VDC mode: 44.6 – 45.3 VDC; 5 A (7.5 A in boost mode for 3min)

Efficiency

– Normal mode

94 – 98 % (battery charged)

(load >50 % of Iout max.)

– Buffer mode

87 – 92 %

General Specifications

Operating temperature

– Normal Mode

–25°C to +70°C max. (without derating)

– Buffer Mode nominal

24 VDC mode: derating above +50°C : 2.0 %/K

48 VDC mode: derating above +40°C : 2.0 %/K

– Buffer Mode boost

24 VDC mode: up to +40°C for 10 minutes max.

48 VDC mode: up to +40°C for 3 minutes max.

Storage temperature

–25°C to +85°C max.

Temperature coefficient

0.02 %/K

Humidity (non condensing)

95 % rel. H max.

Reliability, calculated MTBF at +25°C acc. to IEC 61709

> 1.5 Mio. h

Battery protection

against over voltage, deep discharge, overcharge,

short circuit and reverse connection (built-in fuse)

Signals

– Status

DC OK input, DC OK output, BAT OK

all relay contact closed and LED on at status OK

– Contact rating

30 VDC, 1.0 A max. / 60 VDC, 0.5 A max.

Battery charging current

0.8 – 1.2 A

Nominal battery voltage (at 25ºC)

13.6 VDC (factory setting)

Battery voltage adjustment range

13.2 – 14.4 VDC

Battery restistance test

100mOhm min. (normal mode at 25ºC)

Battery test current

2.5A / 60ms typ. (normal mode at 25ºC)

Battery test interval (acc. to jumper setting)

15s or 10min

Battery warning

10.4 – 11.4 VDC (buffer mode only)

Battery disconnection

9.1 – 9.7 VDC (buffer mode only)

Battery remote Off

disconnects battery in buffer mode (see page 6 - connector)

Automatic battery temperature compensation range

–15ºC – 50ºC

Degree of protection

IP 20 (IEC/EN 60529)

Altitude during operation

2000 m

Safety standard

IEC/EN 60950-1, UL 60950-1 (2nd) + Am1:2011

UL508 – requirements

IEC/EN 61010-1, IEC/EN 61010-2-201

Safety approvals

– CSA

UL60950, UL508

– CB test certificate

IEC 60950-1 (SIQ for EN)

IEC/EN 61010-1, IEC/EN 61010-2-201

– Certification documents

www.tracopower.com/overview/tsp-bcmu

Electromagnetic compatibility

in correspondence to connected unit (no internal switching device)

Environment

– Vibration acc. IEC 60068-2-6;

3 axis, sine sweep, 10 – 55 Hz, 1 g, 1 oct/min

– Shock acc. IEC 60068-2-27

3 axis, 15 g half sine, 11 ms

Enclosure material

aluminium (chassis) / stainless steel (cover)

Mounting

– DIN-rail mounting

for DIN-rails as per EN 50022-35x15/7.5

(snap-on with self-locking spring)

– Wall mounting (option)

with wall mounting bracket - see page 7

Connection

– Input Output battery

screw terminal (plug included)

– Signal & control

detachable screw terminals (plugs included)