| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC16F15213T-I/ST bảng dữ liệu(PDF) 320 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC16F15213T-I/ST bảng dữ liệu(HTML) 320 Page - Microchip Technology |
|
320 / 439 page ![]() 27.1.1 Port Configuration The ADC will convert the voltage on a pin whether or not the ANSEL bit is set. When converting analog signals, the I/O pin may be configured for analog by setting the associated TRIS and ANSEL bits. Refer to the “I/O Ports” section for more information. Important: Analog voltages on any pin that is defined as a digital input may cause the input buffer to conduct excess current. 27.1.2 Channel Selection The Analog Channel Select (CHS) bits determine which channel is connected to the Sample-and-Hold circuit for conversion. When switching channels, it is recommended to add an acquisition delay before starting the next conversion. Refer to the ADC Operation section for more information. Important: To reduce the chance of measurement error, it is recommended to discharge the Sample- and-Hold capacitor when switching between ADC channels by starting a conversion on a channel connected to VSS and terminating the conversion after the acquisition time has elapsed. If the ADC does not have a dedicated VSS input channel, a free input channel can be connected to VSS and used in place of the dedicated input channel. 27.1.3 ADC Voltage Reference The ADC Positive Voltage Reference Selection (PREF) bits provide control of the positive voltage reference. Refer to the ADC Control Register 1 (ADCON1) for the list of available positive voltage sources. 27.1.4 Conversion Clock The conversion clock source is selected via the ADC Conversion Clock Select (CS) bits. The available clock sources include several derivatives of the system clock (FOSC), as well as a dedicated internal fixed-frequency clock referred to as the ADCRC. The time to complete one bit conversion is defined as the TAD. Refer to Figure 27-2 for complete timing details of the ADC conversion. For a correct conversion, the appropriate TAD specification must be met. Refer to the ADC Timing Specifications table in the “Electrical Specifications” section for more details. Table 27-1 gives examples of appropriate ADC clock selections. Important: • With the exception of the ADCRC clock source, any changes in the system clock frequency will change the ADC clock frequency, which may adversely affect the ADC result. • The internal control logic of the ADC operates off of the clock selected by the CS bits. When the CS bits select the ADCRC, there may be unexpected delays in operation when setting the ADC control bits. Table 27-1. ADC Clock Period (TAD) for Different Device Frequencies (FOSC) ADC Clock Source CS[2:0] ADC Clock Period (TAD) for Different Device Frequencies (FOSC) 32 MHz 20 MHz 16 MHz 8 MHz 4 MHz 1 MHz FOSC/2 ‘b000 62.5 ns(2) 100 ns(2) 125 ns(2) 250 ns(2) 500 ns 2.0 µs FOSC/4 ‘b100 125 ns(2) 200 ns(2) 250 ns(2) 500 ns 1.0 µs 4.0 µs PIC16F15213/14/23/24/43/44 ADC - Analog-to-Digital Converter © 2020-2022 Microchip Technology Inc. and its subsidiaries Data Sheet DS40002195E-page 320 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |