MAAPSS0096SMB datasheet(2/6 Pages) MACOM

2 / 6 page

1 Watt Power Amplifier

4.9 - 6.0 GHz

MAAPSS0096

M/A-COM Inc. and its affiliates reserve the right to make changes to the

product(s) or information contained herein without notice. M/A-COM makes

no warranty, representation or guarantee regarding the suitability of its

products for any particular purpose, nor does M/A-COM assume any liability

whatsoever arising out of the use or application of any product(s) or

information.

•

North America Tel: 800.366.2266 / Fax: 978.366.2266

•

Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300

•

Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298

Visit www.macom.com for additional data sheets and product information.

RoHS

Compliant

Recommended Operating Conditions 4,5

4. Operation outside of these ranges may reduce product

reliability.

5. A 100-ohm resistor should be used in the gate voltage line.

Characteristic Symbol Unit

Min.

Typ.

Max.

Drain Voltage

VDD

4.5

7.0

8.0

Gate Voltage 5

VGG

-2.5

-1.8

-1.0

Input Power

dBm

—

Gate Current

IGG

-4

Case Temperature

°C

-40

Electrical Specifications: TC = 40 °C, VDD = 7.0 V, VGG = -1.8 V, Z0 = 50 Ω

Parameter

Test Conditions

Units

Min.

Typ.

Max.

Input VSWR

F = 5.825 GHz, PIN = +14 dBm

—

1.5:1

2.0:1

Gain

F = 5.825 GHz, PIN = 0 dBm

18.0

20.5

—

P1dB

F = 5.825 GHz

dBm

—

29.5

—

Saturated Power

F = 5.825 GHz, PIN = +14 dBm

dBm

29.2

31.5

—

Drain Current at Psat

F = 5.825 GHz, PIN = +14 dBm

—

500

600

2nd Harmonics

3rd Harmonics

Output Power = 29.5 dBm

dBc

—

-40

-70

—

Thermal resistance 3

2nd Stage Only

°C/W

—

Third-Order Intercept Point

dBm

—

Stability

+3 V < VDD < +10 V, PIN< +14 dBm, VSWR < 6:1,

-25 ºC < TC < 85 ºC, RBW = 3 MHz (max. hold)

—

All spurs < -70 dBc

Noise Figure

F = 5.825 GHz

—

5.3

—

3. When using the thermal resistance, you must use the power dissipated by the second stage only (not the total power dissipated). The

second stage dissipates 80% of the total power.

Parameter

Absolute Maximum

Input Power (4.9 - 6.0 GHz)

+ 15 dBm

Operating Voltages

+10 volts

Operating Temperature

-40 °C to +70 °C

Channel Temperature

+150 °C

Storage Temperature

-40 °C to +150 °C

Absolute Maximum Ratings 6,7

Handling Procedures

Please observe the following precautions to avoid

damage:

Static Sensitivity

Gallium Arsenide Integrated Circuits are sensitive

to electrostatic discharge (ESD) and can be

damaged by static electricity. Proper ESD control

techniques should be used when handling these

devices.

6. Exceeding any one or combination of these limits may cause

permanent damage to this device.

7. M/A-COM does not recommend sustained operation near

these survivability limits.

Operating The MAAPSS0096

To operate the device, follow these steps.

1. Apply VGG = -1.8 V, VDD= 0 V.

2. Ramp VDD to desired voltage, typically 5 to 7 V.

3. Adjust VGG to set IDQ, (approximately –1.8 V).

4. Set RF input.

5. Power down in reverse sequence . Turn gate voltage

off last.

MAAPSS0096SMB bảng dữ liệu(PDF) 2 Page - Tyco Electronics

MAAPSS0096SMB bảng dữ liệu(HTML) 2 Page - Tyco Electronics

Html Pages

1 2 3 4 5 6

bảng dữ liệu tải về

Link URL