SST26VF032BEUI datasheet(10/76 Pages) MICROCHIP

10 / 76 page

SST26VF032BEUI

DS20006152A-page 10

 2019 Microchip Technology Inc.

4.5.1

WRITE-ENABLE LATCH (WEL)

The Write-Enable Latch (WEL) bit indicates the status

of the internal memory’s Write-Enable Latch. If the

WEL bit is set to ‘1’, the device is write enabled. If the

bit is set to ‘0’ (reset), the device is not write enabled

and does not accept any memory Program or Erase,

Protection Register Write, or Lock-Down commands.

The Write-Enable Latch bit is automatically reset under

the following conditions:

• Power-up

•Reset

• Write-Disable (WRDI) instruction

• Page-Program instruction completion

• Sector-Erase instruction completion

• Block-Erase instruction completion

• Chip-Erase instruction completion

• Write-Block-Protection register instruction

• Lock-Down Block-Protection register instruction

• Program Security ID instruction completion

• Lockout Security ID instruction completion

• Write-Suspend instruction

• SPI Quad Page program instruction completion

• Write Status Register

4.5.2

WRITE SUSPEND ERASE STATUS

(WSE)

The Write Suspend-Erase status (WSE) indicates

when an Erase operation has been suspended. The

WSE bit is ‘1’ after the host issues a suspend command

during an Erase operation. Once the suspended Erase

resumes, the WSE bit is reset to ‘0’.

4.5.3

WRITE SUSPEND PROGRAM

STATUS (WSP)

The Write Suspend-Program status (WSP) bit indicates

when a Program operation has been suspended. The

WSP is ‘1’ after the host issues a suspend command

during the Program operation. Once the suspended

Program resumes, the WSP bit is reset to ‘0’.

4.5.4

WRITE PROTECTION LOCK-DOWN

STATUS (WPLD)

The Write Protection Lock-Down status (WPLD) bit

indicates when the Block-Protection register is locked-

down to prevent changes to the protection settings.

The WPLD is ‘1’ after the host issues a Lock-Down

Block-Protection command. After a power cycle, the

WPLD bit is reset to ‘0’.

4.5.5

SECURITY ID STATUS (SEC)

The Security ID Status (SEC) bit indicates when the

Security ID space is locked to prevent a Write com-

mand. The SEC is ‘1’ after the host issues a Lockout

SID command. Once the host issues a Lockout SID

command, the SEC bit can never be reset to ‘0.’

4.5.6

BUSY

The Busy bit determines whether there is an internal

Erase or Program operation in progress. If the BUSY

bit is ‘1’, the device is busy with an internal Erase or

Program operation. If the bit is ‘0’, no Erase or Program

operation is in progress.

4.5.7

CONFIGURATION REGISTER

The Configuration register is a Read/Write register that

stores a variety of configuration information. See Table

4-3 for the function of each bit in the register.

TABLE 4-3:

CONFIGURATION REGISTER

Bit

Name

Function

Default at Power-up

Read/Write (R/W)

0RES

Reserved

IOC

I/O Configuration for SPI Mode

1 = WP# and HOLD# pins disabled

0 = WP# and HOLD# pins enabled

1. SST26VF032BEUI default at Power-up is ‘0’

SST26VF032BEUI default at Power-up is ‘1’

R/W

2RES

Reserved

BPNV

Block-Protection Volatility State

1 = No memory block has been permanently locked

0 = Any block has been permanently locked

4RES

Reserved

5RES

Reserved

6RES

Reserved

WPEN

Write-Protection Pin (WP#) Enable

1 = WP# enabled

0 = WP# disabled

2. Factory default setting. This is a non-volatile bit; default at power-up will be the setting prior to power-down.

R/W

SST26VF032BEUI bảng dữ liệu(PDF) 10 Page - Microchip Technology

SST26VF032BEUI bảng dữ liệu(HTML) 10 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76

bảng dữ liệu tải về

Link URL