| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LCS7260C bảng dữ liệu(PDF) 9 Page - Power Integrations, Inc. |
|
|
|||||||||||||||||||||||||||||
LCS7260C bảng dữ liệu(HTML) 9 Page - Power Integrations, Inc. |
|
9 / 35 page ![]() Rev. D 11/22 9 HiperLCS-2 www.power.com Secondary Device PS Pin Error Fault Codes Bit Hex Code Fault Action PS Pin Error Fault Name Description 31:28 X I 1111 Fixed Pre-amble. 27:24 X I 0000 Fixed Pre-amble. 23:18 X N xxxxxx 17:16 X I FREQ_MODE_INFO Information only: read-out of the Secondary device internal Frequency Range 0-3 value. Helpful for debugging frequency confirmation faults (FREQ_FAULT), reported on the primary device. 15:14 X N xx 13 2000h P BPS UV FLT BPS undervoltage fault. This causes the secondary controller to stop operating and enter power-up state. 12 1000h N x 11 800h A SEC_FB_OV_FLT FB pin overvoltage fault. Note: this fault is only active after hand over to secondary control. 10 400h N x 9 200h N x 8:7 X N xx 6 40h A SEC_OT_FAULT Secondary controller over-temperature fault. Device switching stops while fault is active. 5 20h I SEC_PHINV_FAULT Phase inversion fault is only active after start-up and hand over to secondary control mode. The V IS clock is compared to the internal FL clock. If the two clocks are out of phase during 800 ms fault timer, the fault is asserted. Cumulative switching cycles with phase inversion are required. A single switching cycle without phase inversion resets the fault timer. 4:3 X N x 2 4h A VOUT_UV_FLT Output UV Fault become active after start-up and hand over to secondary mode. Fault is activated if FB pin remains below V FBBSTN(TH) for 64 ms. This fault is disabled in CC mode (PPsel6, PPsel7). 1 X N x 0 1h A VFB_START_FLT Secondary start-up fault. From end of frequency confirmation (before hand over), secondary output voltage (monitored by FB pin), if output does not reach regulation within 64 ms, the fault is activated. This fault is disabled in CC mode (PPsel6, PPsel7). Fault Action: A = auto-restart, P = power-up reset state, I = information only, N = not-used (ignore). Table 4. LSR2000C – Secondary-Side PS Pin Error Fault Reporting. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |