| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TLS2205DLR bảng dữ liệu(PDF) 19 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TLS2205DLR bảng dữ liệu(HTML) 19 Page - Texas Instruments |
|
19 / 31 page ![]() SLFS040 – DECEMBER 1993 POST OFFICE BOX 655303 DALLAS, TEXAS 75265 19 PRINCIPLES OF OPERATION serial-port timing The TLS2205 is designed to receive data in four basic formats: TMS320C2x burst mode, TMS320C2x continuous mode, 8-bit microprocessor format mode, and 16-bit microprocessor format mode. The serial port uses three control lines: SCLK (serial-port clock), SDATA (serial-port data), and SPSZ (serial-port select not). The SCLK line is a serial data clock with data rates up to 12 MHz; SCLK should have a 50% duty cycle. The SDATA line is the actual serial data input and must be synchronous with the leading edge of SCLK. SPSZ is the serial-port select input and is internally tied low to be synchronous with the leading edge of SCLK. If the TMS320C2x DSP is used in burst or continuous modes, the following bits in the ST1 register should be set (1) or reset (0) as indicated: BIT NAME BIT # SET/RESET RESULT TXM (transmit mode) 2 1 FSX is configured as an output FO (format) 3 0 16-bit mode selected FSM (framing sync) 5 1 A framing sync is generated Refer to the TMS320C2x User ’s Guide for further details. burst mode In the serial-port burst-mode operation, transfers are separated in time by periods of no serial-port activity (the serial port does not operate continuously). For burst-mode operation, the SPSZ line must be low on the negative-going edge of SCLK before data is read in; then 16 data bits can be read in. All continuing data bits are ignored until the SPSZ line is toggled from low to high to low. Then data is valid on the first negative-going clock. See Figure 8 for details. SCLK SPSZ SDATA Frame Sync ID1 12 Data Bits Device Port ID0 PT1 PT0 SR11 SR10 SR11 SR9 SR8 SR7 SR6 SR5 SR4 SR3 SR2 SR1 SR0 ID1 ID0 PT1 PT0 NOTE: ID1 must be the first bit shifted into the register; after 15 shifts, the TLS2205 is selected and the desired port is loaded with valid data. Figure 8. Serial-Port Burst-Mode Operation |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |