| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STM32H753II bảng dữ liệu(PDF) 189 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32H753II bảng dữ liệu(HTML) 189 Page - STMicroelectronics |
|
189 / 361 page ![]() DS12117 Rev 8 189/360 STM32H753xI Electrical characteristics (rev Y) 318 6.3.32 Communications interfaces I2C interface characteristics The I2C interface meets the timings requirements of the I2C-bus specification and user manual revision 03 for: • Standard-mode (Sm): with a bit rate up to 100 kbit/s • Fast-mode (Fm): with a bit rate up to 400 kbit/s. • Fast-mode Plus (Fm+): with a bit rate up to 1Mbit/s. The I2C timings requirements are guaranteed by design when the I2C peripheral is properly configured (refer to RM0433 reference manual) and when the i2c_ker_ck frequency is greater than the minimum shown in the table below: The SDA and SCL I/O requirements are met with the following restrictions: • The SDA and SCL I/O pins are not “true” open-drain. When configured as open-drain, the PMOS connected between the I/O pin and VDD is disabled, but still present. • The 20 mA output drive requirement in Fast-mode Plus is not supported. This limits the maximum load Cload supported in Fm+, which is given by these formulas: tr(SDA/SCL)=0.8473xRpxCload Rp(min)= (VDD-VOL(max))/IOL(max) Where Rp is the I2C lines pull-up. Refer to Section 6.3.15: I/O port characteristics for the I2C I/Os characteristics. All I2C SDA and SCL I/Os embed an analog filter. Refer to Table 104 for the analog filter characteristics: Table 103. Minimum i2c_ker_ck frequency in all I2C modes Symbol Parameter Condition Min Unit f(I2CCLK) I2CCLK frequency Standard-mode 2 MHz Fast-mode Analog filter ON DNF=0 8 Analog filter OFF DNF=1 9 Fast-mode Plus Analog filter ON DNF=0 17 Analog filter OFF DNF=1 16 Table 104. I2C analog filter characteristics(1) 1. Guaranteed by design. Symbol Parameter Min Max Unit tAF Maximum pulse width of spikes that are suppressed by the analog filter 50(2) 2. Spikes with widths below tAF(min) are filtered. 260(3) 3. Spikes with widths above tAF(max) are not filtered. ns |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |