STM32H753II datasheet(46/361 Pages) STMICROELECTRONICS

46 / 361 page

Functional overview

STM32H753xI

46/360

DS12117 Rev 8

3.31

Inter-integrated circuit interface (I2C)

STM32H753xI devices embed four I2C interfaces.

The I2C bus interface handles communications between the microcontroller and the serial

I2C bus. It controls all I2C bus-specific sequencing, protocol, arbitration and timing.

The I2C peripheral supports:

•

I2C-bus specification and user manual rev. 5 compatibility:

–

Slave and Master modes, multimaster capability

–

Standard-mode (Sm), with a bitrate up to 100 kbit/s

–

Fast-mode (Fm), with a bitrate up to 400 kbit/s

–

Fast-mode Plus (Fm+), with a bitrate up to 1 Mbit/s and 20 mA output drive I/Os

–

7-bit and 10-bit addressing mode, multiple 7-bit slave addresses

–

Programmable setup and hold times

–

Optional clock stretching

•

System Management Bus (SMBus) specification rev 2.0 compatibility:

–

Hardware PEC (Packet Error Checking) generation and verification with ACK

control

–

Address resolution protocol (ARP) support

–

SMBus alert

•

Power System Management Protocol (PMBusTM) specification rev 1.1 compatibility

•

Independent clock: a choice of independent clock sources allowing the I2C

communication speed to be independent from the PCLK reprogramming.

•

Wakeup from Stop mode on address match

•

Programmable analog and digital noise filters

•

1-byte buffer with DMA capability

3.32

Universal synchronous/asynchronous receiver transmitter

(USART)

STM32H753xI devices have four embedded universal synchronous receiver transmitters

(USART1, USART2, USART3 and USART6) and four universal asynchronous receiver

transmitters (UART4, UART5, UART7 and UART8). Refer to Table 6 for a summary of

USARTx and UARTx features.

These interfaces provide asynchronous communication, IrDA SIR ENDEC support,

multiprocessor communication mode, single-wire Half-duplex communication mode and

have LIN Master/Slave capability. They provide hardware management of the CTS and RTS

signals, and RS485 Driver Enable. They are able to communicate at speeds of up to

12.5 Mbit/s.

USART1, USART2, USART3 and USART6 also provide Smartcard mode (ISO 7816

compliant) and SPI-like communication capability.

The USARTs embed a Transmit FIFO (TXFIFO) and a Receive FIFO (RXFIFO). FIFO mode

is enabled by software and is disabled by default.

STM32H753II bảng dữ liệu(PDF) 46 Page - STMicroelectronics

STM32H753II bảng dữ liệu(HTML) 46 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL