| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
SI3232 bảng dữ liệu(PDF) 45 Page - Silicon Laboratories |
|
|
|||||||||||||||||||||||||||||
SI3232 bảng dữ liệu(HTML) 45 Page - Silicon Laboratories |
|
45 / 128 page ![]() Si3232 Preliminary Rev. 0.96 45 4.12.1. Polarity Reversal The Si3232 supports polarity reversal for message- waiting functionality as well as various signaling modes. The ramp rate can be programmed for a smooth transition or an abrupt transition to accommodate different application requirements. A wink function is also provided for special equipment that responds to a smooth ramp to VOC = 0 V. Table 27 illustrates the register bits required to program the polarity-reversal modes. An immediate reversal (hard reversal) of the line polarity is achieved by setting the Linefeed register to the opposite polarity. For example, a transition from Forward Active mode to Reverse Active mode is achieved by changing LF[2:0] from 001 to 101. Polarity reversal can also be accommodated in the OHT and ground-start modes. The POLREV bit is a read-only bit that reflects whether the device is in polarity reversal mode. A smooth polarity reversal is achieved by setting the PREN bit to 1 and setting the RAMP bit to 0 or 1 depending on the desired ramp rate (see Table 27). Polarity reversal is then accomplished by toggling the linefeed register from forward to reverse modes as desired. A wink function is used to slowly ramp down the TIP- RING voltage (VOC) to 1 followed by a return to the original VOC value (set in the VOC RAM 0 location). This scheme is used to light a message-waiting lamp in certain handsets. To enable this function, no change to the linefeed register is necessary. Instead, the user must set the VOCZERO bit to 1 to cause the TIP-RING voltage to collapse to 0 V at the rate programmed by the RAMP bit. Setting the VOCZERO bit back to 0 causes the TIP-RING voltage to return to its normal setting. A software timer provided by the user can automate the cadence of the wink function. Figure 23 illustrates the wink function. Table 27. Register and RAM Locations used for Polarity Reversal Parameter Programmable Range Register/RAM Bits Location Linefeed See Table 12 LF[2:0] LINEFEED Polarity Reversal Status Read only POLREV POLREV Wink Function (Smooth transition to Voc = 0 V) 1 = Ramp to 0 V 0 = Return to previous VOC VOCZERO POLREV Smooth Polarity Reversal Enable 0 = Disabled 1=Enabled PREN POLREV Smooth Polarity Reversal Ramp Rate 0=1 V/125µs 1=2 V/125µs RAMP POLREV |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |