PIC16F87-ISLASHML datasheet(175/214 Pages) MICROCHIP

175 / 214 page

 2003 Microchip Technology Inc.

Preliminary

DS30487B-page 173

PIC16F87/88

18.4

DC Characteristics:

PIC16F87/88 (Industrial, Extended)

PIC16LF87/88 (Industrial)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

≤ TA ≤ +85°C for industrial

-40°C

≤ TA ≤ +125°C for extended

Operating voltage VDD range as described in DC Specification,

Section 18.1 “DC Characteristics: Supply Voltage”.

Param

No.

Sym

Characteristic

Min

Typ†

Max

Units

Conditions

VIL

Input Low Voltage

I/O ports:

D030

with TTL buffer

VSS

—0.15 VDD

For entire VDD range

D030A

VSS

—0.8V

4.5V

≤ VDD ≤ 5.5V

D031

with Schmitt Trigger buffer

VSS

—

0.2 VDD

D032

MCLR, OSC1 (in RC mode)

VSS

—

0.2 VDD

(Note 1)

D033

OSC1 (in XT and LP mode)

VSS

—0.3V

OSC1 (in HS mode)

VSS

—

0.3 VDD

Ports RB1 and RB4:

D034

with Schmitt Trigger buffer

VSS

—

0.3 VDD

For entire VDD range

VIH

Input High Voltage

I/O ports:

D040

with TTL buffer

2.0

—

VDD

V4.5V

≤ VDD ≤ 5.5V

D040A

0.25 VDD + 0.8V

—

VDD

For entire VDD range

D041

with Schmitt Trigger buffer

0.8 VDD

—VDD

For entire VDD range

D042

MCLR

0.8 VDD

—VDD

D042A

OSC1 (in XT and LP mode)

1.6V

—

VDD

OSC1 (in HS mode)

0.7 VDD

—VDD

D043

OSC1 (in RC mode)

0.9 VDD

—VDD

(Note 1)

Ports RB1 and RB4:

D044

with Schmitt Trigger buffer

0.7 VDD

—VDD

For entire VDD range

D070

IPURB PORTB Weak Pull-up Current

250

400

µAVDD = 5V, VPIN = VSS

IIL

Input Leakage Current (Notes 2, 3)

D060

I/O ports

—

±1

µAVss ≤ VPIN ≤ VDD, pin at

high-impedance

D061

MCLR

——

±5

µAVss ≤ VPIN ≤ VDD

D063

OSC1

—

±5

µAVss ≤ VPIN ≤ VDD, XT, HS

and LP osc configuration

These parameters are characterized but not tested.

† Data in "Typ" column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only

and are not tested.

Note 1:

In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the

PIC16F87/88 be driven with external clock in RC mode.

The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels

represent normal operating conditions. Higher leakage current may be measured at different input voltages.

Negative current is defined as current sourced by the pin.

PIC16F87-I/ML bảng dữ liệu(PDF) 175 Page - Microchip Technology

PIC16F87-I/ML bảng dữ liệu(HTML) 175 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL