công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

TMUXHS221 bảng dữ liệu(PDF) 13 Page - Texas Instruments

Click here to check the latest version.
tên linh kiện TMUXHS221
Giải thích chi tiết về linh kiện  TMUXHS221 USB 2.0 480 Mbps 2:1/1:2 Multiplexer/Demultiplexer Switch
PDF  21 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  TI [Texas Instruments]
Trang chủ  http://www.ti.com
Logo TI - Texas Instruments

TMUXHS221 bảng dữ liệu(HTML) 13 Page - Texas Instruments

Back Button TMUXHS221 Datasheet HTML 9Page - Texas Instruments TMUXHS221 Datasheet HTML 10Page - Texas Instruments TMUXHS221 Datasheet HTML 11Page - Texas Instruments TMUXHS221 Datasheet HTML 12Page - Texas Instruments TMUXHS221 Datasheet HTML 13Page - Texas Instruments TMUXHS221 Datasheet HTML 14Page - Texas Instruments TMUXHS221 Datasheet HTML 15Page - Texas Instruments TMUXHS221 Datasheet HTML 16Page - Texas Instruments TMUXHS221 Datasheet HTML 17Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 21 page
background image
9 Power Supply Recommendations
The TMUXHS221 does not require a power supply sequence. However, TI recommends that the device is
enabled after VCC is stable and in specification. TI also recommends to place ample decoupling capacitors at
the device VCC near the pin.
10 Layout
10.1 Layout Guidelines
Place supply bypass capacitors as close to the VCC pin as possible. Avoid placing the bypass capacitors
near the D+/D–traces. The high-speed D+/D– traces should always be matched and must be no more than
4 inches, otherwise the eye diagram performance may be degraded. A high-speed USB connection is made
through a shielded, twisted pair cable with a differential characteristic impedance. In the layout, the impedance
of D+ and D– traces should match the cable characteristic differential impedance for optimal performance.
Route the high-speed USB signals using a minimum of vias and corners which will reduce signal reflections
and impedance changes. When a via must be used, increase the clearance size around it to minimize its
capacitance. Each via introduces discontinuities in the signal’s transmission line and increases the chance of
picking up interference from the other layers of the board. Be careful when designing test points on twisted pair
lines; through-hole pins are not recommended.
When it becomes necessary to turn 90°, use two 45° turns or an arc instead of making a single 90° turn. This
reduces reflections on the signal traces by minimizing impedance discontinuities. Do not route USB traces under
or near crystals, oscillators, clock signal generators, switching regulators, mounting holes, magnetic devices, or
IC’s that use or duplicate clock signals. Avoid stubs on the high-speed USB signals because they cause signal
reflections. If a stub is unavoidable, then the stub should be less than 200 mm. Route all high-speed USB signal
traces over continuous planes (VCC or GND) with no interruptions. Avoid crossing over anti-etch, commonly
found with plane split.
For high speed layout guidelines, refer to High-Speed Layout Guidelines for Signal Conditioners and USB Hubs
application note.
10.2 Layout Example
Figure 10-1 shows TMUXHS221 layout example.
Figure 10-1. TMUXHS221 Layout Example
www.ti.com
TMUXHS221
SLASF52 – AUGUST 2022
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TMUXHS221



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com