CMP 0603 - F X - 1002 E LF

Model

CMP = High Power Anti-Surge Resistor

Size

0603 = 0603 Size

0805 = 0805 Size

1206 = 1206 Size

2010 = 2010 Size

2512 = 2512 Size

Resistance Tolerance

F = ±1 %

J = ±5 %

TCR (See Electrical Characteristics chart)

W = ±200 PPM/°C

X = ±100 PPM/°C

Resistance Value

1 % Tolerance:

<100 Ω..............“R” represents decimal point (example: 24R3 = 24.3 Ω)

≥100 Ω..............First three digits are significant, fourth digit represents number of zeros to follow

(example: 8252 = 82.5K Ω)

5 % Tolerance:

≥10 Ω................First two digits are significant, third digit represents number of zeros to follow

(example: 474 = 470K Ω)

Packaging

E = 5,000 pieces on 180 mm (7 inch) plastic reel, paper tape - CMP0603, CMP0805, CMP1206

4,000 pieces on 180 mm (7 inch) reel, plastic tape - CMP2010, CMP2512

Termination

LF = Tin-plated (RoHS Compliant)

How to Order

Performance Characteristics

Test

Procedure (IEC 60115-1)

Test Limits ΔR

Short Time Overload

5 times rated power for 5 seconds

1 % Tolerance: ≤ ± (1 % + 0.05 Ω)

5 % Tolerance ≤ ± (2 % + 0.05 Ω)

Temperature Cycling

Repeat 5 cycles as follows:

-55 °C (30 min.) --> 25 °C (2-3 min.)--> 155 °C (30 min.)

--> 25 °C (2~3 min.)

1 % Tolerance ≤ ± (0.5 % + 0.05 Ω)

5 % Tolerance ≤ ± (1 % + 0.05 Ω)

Load Life

1.5 hours at rated voltage followed by a pause of 0.5 hour at 70 ± 2 °C;

Cycle repeated for 1000 hours

1 % Tolerance ≤ ± (1 % + 0.05 Ω)

5 % Tolerance ≤ ± (3 % + 0.05 Ω)

Load Life with Humidity

40 ±2 °C with 90~95 % relative humidity;

DC rated voltage for 1.5 hours “ON”, 0.5 hour “OFF”;

Cycle repeated for 1000 hours

1 % Tolerance ≤ ± (1 % + 0.05 Ω)

5 % Tolerance ≤ ± (3 % + 0.05 Ω)

Resistance to Solder

Heat

260 ±5 °C for 10 ±1 seconds

1 % Tolerance ≤ ± (0.5 % + 0.05 Ω)

5 % Tolerance ≤ ± (1 %) + 0.05 Ω

Solderability

After immersing flux, dip in 245 ±2 °C molten solder bath for 3 ± 0.5

seconds

At least 95 % of termination must be

covered with solder..

Board Flex

Bending 2 mm

1 % Tolerance ≤ ± (0.5 % + 0.05 Ω)

5 % Tolerance ≤ ± (1 % + 0.05 Ω)

Specifications are subject to change without notice.

Users should verify actual device performance in their specific applications.

CMP Series High Power Anti-Surge Chip Resistors