LTC4215CUFD datasheet(17/28 Pages) LINER

17 / 28 page

LTC4215/LTC4215-2

4215fe

APPLICATIONS INFORMATION

pin low. The undervoltage lockout circuit has a 2μs ﬁlter

time after VDD drops below 2.74V. The UV pin reacts in

2μs to shut the GATE off, but it is recommended to add a

ﬁlter capacitor CF to prevent unwanted shutdown caused

by a transient. Eventually either the UV pin or undervoltage

lockout responds to bring the current under control before

the supply completely collapses.

Supply Transient Protection

The LTC4215 is safe from damage with supply voltages up

to 24V. However, spikes above 24V may damage the part.

During a short-circuit condition, large changes in current

ﬂowing through power supply traces may cause inductive

voltage spikes which exceed 24V. To minimize such spikes,

the power trace inductance should be minimized by using

wider traces or heavier trace plating. Also, a snubber circuit

dampens inductive voltage spikes. Build a snubber by using

a 100

Ω resistor in series with a 0.1μF capacitor between

VDD and GND. A surge suppressor, Z1 in Figure 1, at the

input can also prevent damage from voltage surges.

Design Example

As a design example, take the following speciﬁcations:

VIN = 12V, IMAX = 5A, IINRUSH = 1A, dI/dtINRUSH = 10A/ms,

CL = 330μF, VUV(ON) = 10.75V, VOV(OFF) = 14.0V, VPWRGD(UP)

= 11.6V, and I2C ADDRESS = 1010011. This completed

design is shown in Figure 1.

Selection of the sense resistor, RS, is set by the overcurrent

threshold of 25mV:

MAX

0 005

The MOSFET is sized to handle the power dissipation dur-

ing inrush when output capacitor COUT is being charged.

A method to determine power dissipation during inrush

is based on the principle that:

Energy in CL = Energy in Q1

This uses:

Energy in CL ==

()( )

033

or 0.024 joules. Calculate the time it takes to charge up

COUT:

STARTUP

INRUSH

•.

•

033

The power dissipated in the MOSFET:

DISS

STARTUP

Energy in CL

TheSOA(safeoperatingarea)curvesofcandidateMOSFETs

must be evaluated to ensure that the heat capacity of the

package tolerates 6W for 4ms. The SOA curves of the

Fairchild FDC653N provide for 2A at 12V (24W) for 10ms,

satisfying this requirement. Since the FDC653N has less

than 8μF of gate capacitance and we are using a GATE

RC network, the short circuit stability of the current limit

should be checked and improved by adding a capacitor

from GATE to SOURCE if needed.

The inrush current is set to 1A using C1:

CmF

μA

or C

GATE

INRUSH

10 33

•

.•

8nF

The inrush dI/dt is set to 10A/ms using CSS:

dI dt

μA

SENSE

⎛

⎝⎜

⎞

⎠⎟

•.

•

0 0375

1000

0 0375

•.

•

LTC4215CUFD bảng dữ liệu(PDF) 17 Page - Linear Technology

LTC4215CUFD bảng dữ liệu(HTML) 17 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

bảng dữ liệu tải về

Link URL