Group A

Subgroup

-

1, 2, 3

1,2,3

1

2, 3

1

2, 3

1

2,3

-

-

4

5,6

1

2,3

-

4

5,6

4

4

4

-

4

4

5,6

4

4

STATIC

Supply Voltage Range

Quiescent Current

Power Consumption

INPUT

Input Capacitance

Input Resistance

Input Noise Voltage

OUTPUT

Settling Time

TRANSFER CHARACTERISTICS

Slew Rate

Transition Times

Overshoot

Max.

±18

±4.0

120

±5.0

-

±500

-

±300

-

-

-

-

-

-

-

-

-

-

-

1.7

250

-

-

-

-

1.2

20

Typ.

±15

±1.0

90

±0.5

-

±150

-

±2.0

-

3

1.0

90

-

95

-

5

±14

-

±12

1.2

150

4

3.0

105

-

0.3

5

Min.

±12

-

-

-

-

-

-

-

-

-

0.3

70

-

80

-

-

±13.0

-

±10.5

0.7

50

-

1.2

100

-

-

-

Max.

±18

±3.5

105

±3.0

±5.0

±300

±1.0

±100

±300

-

-

-

-

-

-

-

-

-

-

1.6

250

-

-

-

-

1.0

20

Typ.

±15

±1.0

75

±0.5

±2.0

±100

±0.4

±2.0

-

3

1.0

90

90

95

-

5

±14

±14

±12

1.2

150

4

3.0

105

96

0.3

5

Min.

±12

-

-

-

-

-

-

-

-

-

0.3

70

70

80

80

-

±13.5

±13.5

±11

0.8

50

-

1.5

100

88

-

-

Either Input

F=DC

F=DC

0.1% 2V step

Ω

Rise and Fall

Small Signal

±18V

Peak Output Current

2A

Differential Input Voltage

±30V

Common Mode Input Voltage

±15V

Thermal Resistance-Junction to Case

MSK 0021

2.0° C/W

MSK 0021FP/FPG

6.0° C/W

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL SPECIFICATIONS

Storage Temperature Range

-65° to +150°C

Lead Temperature Range

300°C

(10 Seconds)

Power Dissipation (TO-3)

6W

Junction Temperature

150°C

Case Operating Temperature Range

Military Versions (H/B/E)

-55°C to +125°C

Industrial Versions

-40°C to +85°C

Units

V

mA

mW

mV

µV/°C

nA

µA

nA

nA

pF

M

Ω

dB

dB

dB

dB

V

V

V

A

mA

µS

V/µS

dB

dB

µS

%

2

Rev. A 6/03

Military

Industrial

2

Input Bias Current

Output Voltage Swing

Parameter

Test Conditions

4

Input Offset Current

Input Offset Voltage

Power Supply Rejection Ratio

Output Short Circuit Current

Common Mode Rejection Ratio

Open Loop Voltage Gain

NOTES:

1

2

Guaranteed by design but not tested.

Typical parameters are representative of actual device performance but are for reference only.

4

Industrial grade and "E" suffix devices shall be tested to subgroups 1 and 4 unless otherwise specified.

5

Military grade devices (B/H suffix) shall be 100% tested to subgroups 1, 2, 3 and 4.

Subgroup 1, 4

+25°C

Subgroup 2, 5

Subgroup 3, 6

-55°C

6

Reference DSCC SMD 5962-8508801 for electrical specifications for devices purchased as such.

7

Subgroup 5 and 6 testing available upon request.

3

2

3

5

2

3

Ω

3