| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
MX584JC/D bảng dữ liệu(PDF) 7 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MX584JC/D bảng dữ liệu(HTML) 7 Page - Maxim Integrated Products |
|
7 / 11 page ![]() Output Current The MX584 is capable of sinking as well as sourcing current. The circuit is also protected for output shorts to either +VS or ground (COMMON). The output’s voltage versus current characteristic is shown in the Typical Operating Characteristics section. For applications that require the MX584 to sink current, maintain a load capacitance of 10nF or greater for proper operation. Dynamic Performance The turn-on settling performance of the MX584 is shown in the Typical Operating Characteristics. Both coarse and fine transient response is shown. The refer- ence typically settles to 1mV (10V output) within 180µs after power is applied. Noise Filtering The bandwidth of the MX584’s output amplifier can be limited by connecting a capacitor between the CAP and VBG pins (see Figure 4). Typical values range from 0.01µF to 0.1µF. The reduction of wideband and feedthrough noise is plotted in a graph in the Typical Operating Characteristics section. Strobe Input The STROBE input, pin 5, zeroes the reference output when it is pulled LOW. If no current is pulled from STROBE, operation is normal. The threshold of the input is 200mV, so an open-drain n-channel FET or open-collector transistor driven from logic is recom- mended (see Figure 5). The current-sinking ability should be at least 500µA and the leakage current should be 5µA or less. While shut down, the MX584 should not be required to source or sink current unless a 0.7V residual output is acceptable. If the reference is required to sink transient current while shut down, the current flowing out of STROBE should be limited with 100Ω as shown in the dashed connection in Figure 5. Applications Information Precision High-Current Reference A PNP power transistor, or Darlington, is easily connect- ed to the MX584 to greatly increase its output current. The circuit in Figure 6 provides a +10V output at up to 4A. If the load has a significant capacitive component, C1 should be added. If the load is purely resistive, high- frequency supply rejection is improved without C1. An NPN output transistor or Darlington can also be used to boost output current as shown in Figure 7. Current Limiter By adding a single resistor as shown in Figure 8, the MX584 is turned into a precision current limiter for Pin-Programmable, Precision Voltage Reference 6 _______________________________________________________________________________________ 10V COM -15V RS 2.4kΩ 5% 5V 5V 0.01µF VREF = -5V +VS 1 2 ANALOG GROUND 4 8 MX584 Figure 9. Two-Terminal -5V Reference RFB VREF GND DIGITAL INPUT 4-13 COM 7.5V to 15V 0 TO -5V -7.5V TO -15V OUT2 OUT1 10V 5V 5V VOUT +VS 1 2 1 2 3 16 14 15 4 8 MX7533 MX584 MAX400 Figure 10. Low-Power, 10-Bit CMOS DAC Connection DGND AGND DIGITAL OUTPUTS COM INPUT 0 TO +2.5V 0.01µF 1kΩ 5% -5V +5V 2.5V -2.5VREF 10V +VS 1 3 18 42 5 1 8 MX584 DB0– DB7 13-6 VREF BOFS AIN VDD MX7574 Figure 11. MX584 as Negative 2.5V Reference for a CMOS ADC |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |