LM124A RAD HARD — DC Drift Values (Note 10)

(The following conditions apply to all the following parameters, unless otherwise specified.) DC: "Delta calculationsperformed

on QMLV devices at group B, subgroup 5 only"

SYMBOL

PARAMETER

CONDITIONS

NOTES

MIN

MAX

UNIT

SUB-

GROUPS

Vio

Input Offset Voltage

Vcc+ = 30V, Vcc- = Gnd,

Vcm = -15V

-0.5

0.5

mV

1

Input Bias Current

Vcc+ = 30V, Vcc- = Gnd,

Vcm = -15V

-10

10

nA

1

Electrical Characteristics — POST RADIATION LIMITS +25˚C (Note 10)

(The following conditions apply to all the following parameters, unless otherwise specified.) All voltages referenced to device

ground.

SYMBOL

PARAMETER

CONDITIONS

NOTES

MIN

MAX

UNIT

SUB-

GROUPS

Vio

Input Offset Voltage

Vcc+ = 30V, Vcc- = Gnd,

Vcm = -15V

(Note 10)

-2.5

2.5

mV

1

Vcc+ = 2V, Vcc- = -28V,

Vcm = 13V

(Note 10)

-2.5

2.5

mV

1

Vcc+ = 5V, Vcc- = GND,

Vcm = -1.4V

(Note 10)

-2.5

2.5

mV

1

Vcc+ = 2.5V, Vcc- = -2.5,

Vcm = 1.1V

(Note 10)

-2.5

2.5

mV

1

Iio

Input Offset Current

Vcc+ = 30V, Vcc- = GND,

Vcm = -15V

(Note 10)

-15

15

nA

1

Vcc+ = 2V, Vcc- = -28V,

Vcm = 13V

(Note 10)

-15

15

nA

1

Vcc+ = 5V, Vcc- = GND,

Vcm = -1.4V

(Note 10)

-15

15

nA

1

Vcc+ = 2.5V, Vcc- = -2.5V,

Vcm = 1.1V

(Note 10)

-15

15

nA

1

Input Bias Current

Vcc+ = 30V, Vcc- = GND,

Vcm = -15V

(Note 10)

-75

+0.1

nA

1

Vcc+ = 2V, Vcc- = -28V,

Vcm = 13V

(Note 10)

-75

+0.1

nA

1

Vcc+ = 5V, Vcc- = GND,

Vcm = -1.4V

(Note 10)

-75

+0.1

nA

1

Vcc+ = 2.5V, Vcc- = -2.5V,

Vcm = 1.1V

(Note 10)

-75

+0.1

nA

1

Avs+

Voltage Gain

Vcc+ = 30V, Vcc- = GND,

1V

≤ Vo ≤ 26V, Rl = 10K Ohms

(Note 10)

40

V/mV

4

Vcc+ = 30V, Vcc- = GND,

5V

≤ Vo ≤ 20V, Rl = 2K Ohms

(Note 10)

40

V/mV

4

Note 6: Guaranteed by Vio tests.

Note 7: Datalog reading in K=V/mV

Note 8: Guaranteed, not tested

Note 9: Calculated parameters

Note 10: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table.

These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters

are guaranteed only for the conditions as specified in MIL-STD-883, Method 1019

www.national.com

11