RTY070LVEAX datasheet(3/10 Pages) HONEYWELL

3 / 10 page

sensing.honeywell.com

Hall-effect Rotary Position Sensors

Table 2. Mechanical Specifications

Characteristic

RTY Series

RTP Series

LV (Low Voltage)

HV (High Voltage)

LV (Low Voltage)

HV (High Voltage)

Expected life

35 M cycles

infinite rotation

Air gap:

bare magnet actuator

housed magnet actuator

misalignment

—

3,00 mm ±0.5 mm [0.12 in ±0.02 in]

2,00 mm ±0.5 mm [0.08 in ±0.02 in]

2.002,00 mm [0.08 in] max.

Material:

shaft

magnet

sensor housing

housed magnet overmold

sensor/housed magnet bushing

sensor bushing

stainless steel

—

PBT plastic

—

stainless steel

—

NdFeB

PBT plastic

PPS plastic

brass

—

Mating connector

AMP Superseal 282087-1

Mechanical end stop

Mounting screw sizes:

sensor to mounting surface

lever to mounting surface

housed magnet actuator to

actuator mounting shaft

non-magnetic, stainless steel M5 screws and

10 mm [0.39 in] OD washers

non-magnetic stainless steel M6 screws,

—

non-magnetic, stainless steel M4 X 0.7 screws and

8 mm [0.31 in] OD washers

—

non-magnetic, stainless steel M3 X 0.5

plain cup point set screws

Approvals

Table 1. Electrical Specifications

Characteristic

RTY Series

RTP Series

LV (Low Voltage)

HV (High Voltage)

LV (Low Voltage)

HV (High Voltage)

Supply voltage

5 ±0.5 Vdc

10 Vdc to 30 Vdc

5 ±0.5 Vdc

10 Vdc to 30 Vdc

Supply current:

normal

during output to ground short

20 mA max.

25 mA max.

32 mA max.

47 mA max.

20 mA max.

25 mA max.

32 mA max.

47 mA max.

Output:

standard

inverted

0.5 Vdc to 4.5 Vdc

ratiometric

4.5 Vdc to 0.5 Vdc

ratiometric

0.5 Vdc to 4.5 Vdc

non-ratiometric

4.5 Vdc to 0.5 Vdc

non-ratiometric

0.5 Vdc to 4.5 Vdc

ratiometric

4.5 Vdc to 0.5 Vdc

ratiometric

0.5 Vdc to 4.5 Vdc

non-ratiometric

4.5 Vdc to 0.5 Vdc

non-ratiometric

Output signal delay

4 ms typ.

Overvoltage protection

10 Vdc

—

10 Vdc

—

Reverse polarity protection

-10 Vdc

-30 Vdc

-10 Vdc

-30 Vdc

Output to ground short circuit

protection

continuous

Resolution

12 bit

Output load resistance

(pull down to ground)

10 kOhm typ.

EMI:

radiated immunity

100 V/m per ISO11452-2 from 200 MHz to 1000 MHz

conducted immunity

100 mA BCI per ISO11452-4

from 1 MHz to 200 MHz

100 mA BCI per ISO11452-4

from 1 MHz to 400 MHz

100 mA BCI per ISO11452-4

from 1 MHz to 200 MHz

100 mA BCI per ISO11452-4

from 1 MHz to 400 MHz

EMC

exceeds CE requirements

RTY070LVEAX bảng dữ liệu(PDF) 3 Page - Honeywell Solid State Electronics Center

RTY070LVEAX bảng dữ liệu(HTML) 3 Page - Honeywell Solid State Electronics Center

Html Pages

1 2 3 4 5 6 7 8 9 10

bảng dữ liệu tải về

Link URL