AT90USB646 datasheet(97/434 Pages) ATMEL

97 / 434 page

7593A–AVR–02/06

AT90USB64/128

• Bits 7..0 – INT7 – INT0: External Interrupt Request 7 - 0 Enable

When an INT7 – INT0 bit is written to one and the I-bit in the Status Register (SREG) is set

(one), the corresponding external pin interrupt is enabled. The Interrupt Sense Control bits in the

External Interrupt Control Registers – EICRA and EICRB – defines whether the external inter-

rupt is activated on rising or falling edge or level sensed. Activity on any of these pins will trigger

an interrupt request even if the pin is enabled as an output. This provides a way of generating a

software interrupt.

11.0.4

External Interrupt Flag Register – EIFR

• Bits 7..0 – INTF7 - INTF0: External Interrupt Flags 7 - 0

When an edge or logic change on the INT7:0 pin triggers an interrupt request, INTF7:0 becomes

set (one). If the I-bit in SREG and the corresponding interrupt enable bit, INT7:0 in EIMSK, are

set (one), the MCU will jump to the interrupt vector. The flag is cleared when the interrupt routine

is executed. Alternatively, the flag can be cleared by writing a logical one to it. These flags are

always cleared when INT7:0 are configured as level interrupt. Note that when entering sleep

mode with the INT3:0 interrupts disabled, the input buffers on these pins will be disabled. This

may cause a logic change in internal signals which will set the INTF3:0 flags. See “Digital Input

Enable and Sleep Modes” on page 77 for more information.

11.0.5

Pin Change Interrupt Control Register - PCICR

• Bit 0 – PCIE0: Pin Change Interrupt Enable 0

When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin

change interrupt 0 is enabled. Any change on any enabled PCINT7..0 pin will cause an

interrupt. The corresponding interrupt of Pin Change Interrupt Request is executed from

the PCI0 Interrupt Vector. PCINT7..0 pins are enabled individually by the PCMSK0 Register.

11.0.6

Pin Change Interrupt Flag Register – PCIFR

• Bit 0 – PCIF0: Pin Change Interrupt Flag 0

When a logic change on any PCINT7..0 pin triggers an interrupt request, PCIF0 becomes set

(one). If the I-bit in SREG and the PCIE0 bit in EIMSK are set (one), the MCU will jump to the

INT7

INT6

INT5

INT4

INT3

INT2

INT1

IINT0

EIMSK

Read/Write

R/W

Initial Value

0000

Bit

7654

INTF7

INTF6

INTF5

INTF4

INTF3

INTF2

INTF1

IINTF0

EIFR

Read/Write

R/W

Initial Value

0000

Bit

–

–PCIE0

PCICR

Read/Write

RR/W

Initial Value

Bit

–

–PCIF0

PCIFR

Read/Write

RR/W

Initial Value

AT90USB646 bảng dữ liệu(PDF) 97 Page - ATMEL Corporation

AT90USB646 bảng dữ liệu(HTML) 97 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL