6

ABSOLUTE MAXIMUM RATINGS

Supply Voltage (VDD33 to GND) ...... -0.3V to +3.8V

Supply Voltage (VDD18 to GND) ..... -0.2 V to +2.2V

Input Voltage (1.8V pins) ... -0.2V to (VDD18 + 0.2V)

Input Voltage (3.3V pins) ... -0.3V to (VDD33 + 0.3V)

Input into the Balun (RMS) ........................... +7dBm

Junction Temperature .................................. +150°C

Storage Temperature .....................-65°C to +150°C

OPERATING RATING

Operating Case Temperature……-40°C to +100°C

Warning: Any stress beyond the ranges indicated may damage

the device permanently. The specified stress ratings do not imply

functional performance in these ranges. Exposure of the device

to the absolute maximum ratings for extended periods of time is

likely to degrade the reliability of this product.

DC CHARACTERISTICS

PARAMETER

MIN

TYP

MAX

UNITS

Supply Voltage (VDD33 to GND)

3.1

3.3

3.5

V

Supply Voltage (VDD18 to GND)

1.7

1.8

1.9

V

Supply Peak Current (VDD33 to GND)

1,2,3, 5

59

mA

Supply Peak Current (VDD18 to GND)

1,2,3, 5

592

mA

Average Power Dissipation: Full-Scale Adaptation, Track, and PMU

3, 5

1060

mW

Average Power Dissipation: Duty-Cycled Feedback

2,4,5

420

mW

Note 1: Peak current includes supply decoupling network. Refer to Hardware Design Guide for proper sizing of the on-board regulators.

Note 2: Characterized at typical voltages, +25°C operating case temperature and 20MHz input signal BW.

Note 3: Continuous adaptation, tracking (100% duty-cycled feedback) and Power Measurement Unit active or inactive.

Note 4: Duty-cycled feedback power dissipations averaged over ON time of 100ms (9%) and OFF time of 1.024s (91%).

Note 5: Power dissipation may be FW dependent. Refer to the FW release notes for any changes to values listed above.

RADIO FREQUENCY SIGNALS

PARAMETER

SYMBOL

CONDITIONS

MIN

RECOMMENDED

MAX

UNITS

Operating Frequency

1

f

698

2800

MHz

RFIN_BLN Range for

Maximum Correction

Peak power

-4

4

6

dBm

RFIN_BLN Range for

Maximum Correction

RMS power

2

-9

-6

-4

dBm

RFFB_BLN Range for

Maximum Correction

Peak power

-14

-4

-2

dBm

RFFB_BLN Range for

Maximum Correction

RMS power

2

-19

-14

-12

dBm

RFIN_BLN

Operating Range

RMS power

2

-40

-4

dBm

RFFB_BLN Operating

Range

RMS power

2

-45

-12

dBm

RF Input Signal

Peak-to Avg. Ratio

3

CCDF

4

probability=10

-4

5 to 10

dB

Input Signal Bandwidth

1.2

40 or 60

5

MHz

Noise Power

6

Referred to

0dBm at PA

input

-138

-135

dBm/Hz

Note 1: See Operating Frequency Ranges table for frequency limits of each defined band.

Note 2: A peak to average ratio (PAR) of 5dB to 10dB is used for this table.

Note 3: Higher PAR values can be supported but at a reduction to a combination of the input signal range and IM correction limits.

Note 4: CCDF = Complementary cumulative distribution function; a measurement of peak to average ratio or crest factor.

Note 5: > 40MHz operation requires a fully occupied signal bandwidth.

Note 6: Worst case over PVT guaranteed by bench characterization.