| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
DA7282-00FVC bảng dữ liệu(PDF) 30 Page - Dialog Semiconductor |
|
|
|||||||||||||||||||||||||||||
DA7282-00FVC bảng dữ liệu(HTML) 30 Page - Dialog Semiconductor |
|
30 / 77 page ![]() DA7282 LRA/ERM Ultra-Low Power Haptic Driver with Multiple Input Triggers and Integrated Waveform Memory Datasheet Revision 3.0 30-Jul-2019 CFR0011-120-00 30 of 77 © 2019 Dialog Semiconductor 5.6.5.4 Register Triggered Waveform Memory (RTWM) Mode The following registers should be set up prior to operation in RTWM mode: ● Set FREQ_WAVEFORM_TIMEBASE according to the minimum or maximum sequence timebase required. ● Set SNP_MEM_x (where x = 0 to 99), see Section 5.8. ● If custom waveform sequences are required, see Section 5.7.5. ● Set WAV_MEM_LOCK = 0 to prohibit access to the waveform memory if required. Figure 15 shows how to operate the device in RTWM mode. 1. While in the IDLE or STANDBY state, configure PS_SEQ_ID and PS_SEQ_LOOP to select the desired sequence from Waveform Memory. 2. For first-time playback, set OPERATION_MODE = 3. On subsequent sequence playbacks, this step can be skipped (if OPERATION_MODE = 3). The haptic sequence will not begin playing until a start event is created by setting SEQ_START = 1. 3. While in the DRIVE state, set SEQ_CONTINUE = 1 to repeat the sequence. 4. When the haptic sequence is completed, DA7282 will signal this by setting nIRQ = 0 and setting SEQ_DONE_M = 1. DA7282 will then return to IDLE or STANDBY state, depending on the value of STANDBY_EN. 5. Clear the nIRQ and SEQ_DONE_M signals, set SEQ_DONE_M =1. 6. At any time during operation in RTWM mode, set OPERATION_MODE or SEQ_START = 0 to return to the IDLE or STANDBY state. Output starts switching Write OPERATION_MODE = 3 IDLE/STANDBY Sequence playback Write SEQ_DONE_M = 1 to clear register and nIRQ DA7282 ready to play next sequence Sequence is continued Are PS_SEQ_ID and PS_SEQ_LOOP already configured? Configure the PS_SEQ_LOOP register Yes No Create a start event by writing to SEQ_START SEQ_CONTINUE = 1? Select a sequence via PS_SEQ_ID No Yes OPERATION_MODE = 3? Yes No nIRQ = 0 and SEQ_DONE_M = 1 Sequence playback is complete and output stops switching SEQ_CONTINUE can be set if required during playback Can be skipped for subsequent sequence playbacks Figure 15: Operation in RTWM Mode |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |