MBA/SMA 0204 VG06, MBB/SMA 0207 VG06, MBE/SMA 0414

www.vishay.com

Vishay Beyschlag

Revision: 27-Feb-2019

5

Document Number: 28768

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

DESCRIPTION

Production is strictly controlled and follows an extensive set

of

instructions

established

for

reproducibility.

A

homogeneous film of metal alloy is deposited on a high

desired temperature coefficient. Plated steel termination

caps are firmly pressed on the metallised rods. A special

laser is used to achieve the target value by smoothly cutting

a helical groove in the resistive layer without damaging the

ceramics. Connecting wires of electrolytic copper plated

with fused pure tin are welded to the termination caps. The

resistor elements are covered by a light blue protective

coating designed for electrical, mechanical and climatic

protection. Five color code rings designate the resistance

The result of the determined production is verified by an

extensive testing procedure performed on 100 % of the

individual resistors. For IECQ-CECC approved products,

this includes pulse load screening for the elimination of

products with a potential risk of early life failures according

to EN 140101-806, 2.1.2.2 (feasible for R

 10 ). Only

accepted products are stuck directly on the adhesive tapes

package unit are from the same production lot and carry the

same date code.

ASSEMBLY

The resistors are suitable for processing on lead forming and

cropping equipment and automatic insertion machines.

They are suitable for automatic wave or reflow soldering,

including miniature wave selective soldering. Solderability is

specified for 2 years after production or requalification,

however, the permitted storage time is 20 years.

The resistors are completely lead (Pb)-free, the fused pure

tin plating provides compatibility with lead (Pb)-free

soldering processes. The immunity of the plating against tin

whisker growth has been proven under extensive testing.

The encapsulation is resistant to all cleaning solvents

commonly used in the electronics industry, including

alcohols, esters and aqueous solutions. The suitability of

conformal

coatings,

potting

compounds,

and

their

processes, if applied, shall be qualified by appropriate

means to ensure the long-term stability of the whole system.

MATERIALS

Vishay acknowledges the following systems for the

regulation of hazardous substances.

• IEC 62474, Material Declaration for Products of and for the

Electrotechnical Industry, with the list of declarable

• The

Global

Automotive

Declarable

Substance

List

• The REACH regulation (1907/2006/EC) and the related list

supply chain

The products do not contain any of the banned substances

as per IEC 62474, GADSL, or the SVHC list, see



Hence the products fully comply with the following

directives:

• 2000/53/EC End-of-Life Vehicle Directive (ELV) and

Annex II (ELV II)

• 2011/65/EU

Restriction

of

the

Use

of

Hazardous

Substances

Directive

(RoHS)

with

amendment

2015/863/EU

• 2012/19/EU Waste Electrical and Electronic Equipment

Directive (WEEE)

Vishay pursues the elimination of conflict minerals from its

supply

chain,

see

the

Conflict

Minerals

Policy

at

APPROVALS

The resistors are approved within the IECQ-CECC Quality

Assessment System for Electronic Components to the detail

specification EN 140101-806 which refers to EN 60115-1,

EN 140100 and the variety of environmental test procedures

Conformity is attested by the use of the CECC logo (

) as

the Mark of Conformity on the package label.

Vishay

Beyschlag

has

achieved

“Approval

of

Manufacturer” in accordance with IECQ 03-1. The release

certificate

for

“Technology

Approval

Schedule”

in

accordance with CECC 240001 based on IECQ 03-3-1 is

granted for the Vishay Beyschlag manufacturing process.

The Vishay Beyschlag production facility is registered with

the CAGE code D9539.

RELATED PRODUCTS

A wider range of TCR, tolerance and resistance values, plus

the option of values from a different E series is available with

products approved to EN 140101-806, version A, without

established reliability, nominal failure rate level E0 (Quality

factor



• “Professional Leaded Metal Film Resistors”



• “Precision Leaded Metal Film Resistors”



Notes

www.gadsl.org