| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
MAX3964C/D bảng dữ liệu(PDF) 6 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX3964C/D bảng dữ liệu(HTML) 6 Page - Maxim Integrated Products |
|
6 / 12 page ![]() +3.0V to +5.5V, 125Mbps to 266Mbps Limiting Amplifiers with Loss-of-Signal Detector 6 _______________________________________________________________________________________ Detailed Description The MAX3964 contains a series of limiting amplifiers and power detectors, offset correction, data-squelch circuitry, and PECL output buffers for data and loss-of- signal (LOS) outputs. The MAX3965 is functionally the same, but it provides TTL buffers on the LOS outputs. The MAX3968 provides PECL LOS outputs with data outputs suitable for 266Mbps. Figure 1 shows a func- tional diagram of the MAX3964/MAX3965/MAX3968. Limiting Amplifiers A series of four limiting amplifiers provides gain of approximately 65dB. Power Detector Each amplifier stage contains a full-wave logarithmic detector (FWD), which indicates the RMS input signal power. The FWD outputs are summed together at the FILTER pin where the signal is filtered by an external capacitor (CFILTER) connected between FILTER and VCC. The FILTER signal generates the RSSI output volt- age, which is proportional to the input power in deci- bels. When LOS+ is low, VRSSI is approximated by the following equation: VRSSI (V) = 1.2V + 0.5log (VIN) where VIN is measured in mVp-p. This relation translates to a 25mV increase in VRSSI for every 1dB increase in VIN (25mV/dB). The RSSI output is reduced approximately 120mV when LOS+ is asserted. PECL Outputs The data outputs (OUT+, OUT-) and the MAX3964/ MAX3968 loss-of-signal outputs (LOS+, LOS-) are sup- ply-referenced PECL outputs. Standard PECL termina- tion at each output of 50Ω to (VCC - 2V) is recommended for best performance. TTL Outputs The MAX3965 LOS outputs (LOS+, LOS-) are imple- mented with open-collector Schottky-clamped TTL- compatible outputs. The LOS outputs are pulled to VCC internally with 2kΩ resistors and do not require external pullup resistors. Input Offset Correction A low-frequency feedback loop around the limiting amplifier improves receiver sensitivity and powerdetec- tor accuracy. The offset-correction loop’s bandwidth is determined by an external capacitor (CAZ) connected between the CZP and CZN pins. The offset correction is optimized for data streams with a 50% duty cycle. A different average duty cycle results in increased pulse-width distortion and loss of CZN CZP OUT+/OUT- LOS+/LOS- RSSI SQUELCH LOS+ LOS COMPARATOR FILTER IN+/IN- VCC VCCO R1 R2 VTR SUB GND GNDO (MAX3965 ONLY) INV VCC CFILTER FWD = FULL-WAVE DETECTOR CAZ LIMITER OFFSET CORRECTION LIMITER I I O LIMITER LIMITER FWD FWD FWD FWD 1.2V REFERENCE MAX3964 MAX3965 MAX3968 Figure 1. Functional Diagram |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |