3M

L1815 • L1715 • L1515 • L1015 • L1315 • L1915 • L1915S • L1215 • L1115

L1820 • L1720 • L1520 • L1020 • L1320 • L1920 • L1920S • L1220 • L1120

Typical Physical Properties

and Performance

Characteristics

Note: The following technical information and data should be considered representative or

typical only and should not be used for specification purposes.

Product

3M

™ Cushion-Mount™ Plus

Standard Combination Plate

Mounting Tapes

3M

™ Cushion-Mount™ Plus

Medium Soft Process Plate

Mounting Tapes

3M

™ Cushion-Mount™ Plus

Light Medium Combination

Plate Mounting Tapes

L1015

L1020

L1315

L1320

L1915

L1920

Adhesive

Differential Acrylate

Differential Acrylate

Differential Acrylate

Polyethylene Carrier

Standard White Foam

Medium Soft Yellow Foam

Light Medium Pink Foam

Type of Printing

Combination of solids and tone

reproduction where solids and

process are equally important

Combination of solids and tone

reproduction where process

printing is important

Combination of solids and

tone reproduction where

process printing is

important

Application Thickness

in

(mm)

0.015

(0.0381)

0.020

(0.508)

0.015

(0.0381)

0.020

(0.508)

0.015

(0.0381)

0.020

(0.508)

Thickness

Tape

in

(mm)

Film Liner

in

(mm)

Lot to Lot Tolerance

in

(mm)

Typical Application Area

in

Caliper Variation

(mm)

0.017

(0.432)

0.022

(0.559)

0.017

(0.432)

0.022

(0.559)

0.017

(0.432)

0.022

(0.559)

0.0045

(0.114)

0.0045

(0.114)

0.0045

(0.114)

0.0045

(0.114)

0.0045

(0.114)

0.0045

(0.114)

±0.0015

(±0.038)

±0.0015

(±0.038)

±0.0015

(±0.038)

±0.0015

(±0.038)

±0.0015

(±0.038)

±0.0015

(±0.038)

±0.0004

(±0.010)

±0.0004

(±0.010)

±0.0004

(±0.010)

±0.0004

(±0.010)

±0.0004

(±0.010)

±0.0004

(±0.010)

Roll Length

yd

(m)

25

(22.9)

25

(22.9)

25

(22.9)

25

(22.9)

25

(22.9)

25

(22.9)

Maximum Width

in

(mm)

54

(1371.6)

54

(1371.6)

54

(1371.6)

54

(1371.6)

54

(1371.6)

54

(1371.6)

Minimum Width

in

(mm)

2

(50.8)

2

(50.8)

2

(50.8)

2

(50.8)

2

(50.8)

2

(50.8)

Slitting Tolerance

in

(mm)

±1/32

(±0.794)

±1/32

(±0.794)

±1/32

(±0.794)

±1/32

(±0.794)

±1/32

(±0.794)

±1/32

(±0.794)

Density

lb/ft

3

28

(450)

28

(450)

27

(433)

27

(433)

26

(416)

26

(416)

Compression Deflection

10% Compression

lb/in

2

(kPa)

25% Compression

lb/in

2

(kPa)

15

(104)

15

(104)

12

(49)

12

(49)

10

(70)

10

(70)

30

(207)

30

(207)

25

(172)

25

(172)

20

(138)

20

(138)

Durometer ASTM-D2240

Shore A

65

65

63

63

60

60

Peel Adhesion (Modified ASTM-D3330)

Non-linered side -

oz/in

Stainless Steel

(N/100mm)

Non-linered side -

oz/in

Composite Sleeve

(N/100mm)

Non-linered side -

oz/in

Polyester

(N/100mm)

Non-linered side -

oz/in

Urethane - A

(N/100mm)

Non-linered side -

oz/in

Urethane - B

(N/100mm)

55

(60)

55

(60)

55

(60)

55

(60)

30

(33)

30

(33)

65

(71)

65

(71)

65

(71)

65

(71)

28

(31)

28

(31)

60

(66)

60

(66)

60

(66)

60

(66)

35

(39)

35

(39)

80

(88)

80

(88)

80

(88)

80

(88)

45

(50)

45

(50)

65

(71)

65

(71)

65

(71)

65

(71)

35

(39)

35

(39)

Peel Adhesion (Modified ASTM-D3330)

Linered side -

oz/in

Photopolymer

(N/100mm)

15

(16)

15

(16)

15

(16)

15

(16)

15

(16)

15

(16)

Solvent Resistance

Water

Alkanes

Alcohols

Acetates

Excellent

Excellent

Good

Fair

Excellent

Excellent

Good

Fair

Excellent

Excellent

Good

Fair

Excellent

Excellent

Good

Fair

Excellent

Excellent

Good

Fair

Excellent

Excellent

Good

Fair

Heat Resistance

°F

(°C)

120

(49)

120

(49)

120

(49)

120

(49)

120

(49)

120

(49)

- 3 -