V11

2

CFM130M Series Derating Curve

INPUT SPECIFICATIONS:

Voltage …....………........…........................................................ 80~264Vac

Frequency ………………………………..………………………..... 47 to 63Hz

Inrush Current ………………….…… Cold start @25℃100A max. @240Vac

Input Current ……….……………..…. 100Vac/1.5A max., 240Vac/0.8Amax.

Leakage Current ……………………..………………….…...…… 100uA max.

OUTPUT SPECIFICATIONS:

Holdup Time …………………………………………… 20ms min. @115Vac

Short Circuit Protection …………….....…….. Hiccup Mode (Auto Recover)

Over Voltag

e Protection ……………………………….……… Auto Recover

Temperature Coefficient …………………….....................… ±0.05%/℃ max.

GENERAL SPECIFICATIONS:

Isolation ………………………………………… Input to output = 4000VAC

Operating Temperature ............................ -30 ~ 70℃ (See Derating Curve)

Storage Temperature ……………………….……...….....……...... -40 ~ 85℃

Humidity …………………...….......……........ 93% RH max. Non condensing

Cooling

…………….. Natural Convection@100W, 10CFM Air Flow@130W

Switching Frequency …………………………………………105 KHz Typical

MTBF ….....… MIL-HDBK-217F, GB, 25℃/115VAC ………. 400 Khrs min.

Altitude …………………………………………………………………… 5000m

Dimensions ……….……… 3.000x2.000x1.20 inches (76.2x50.8x30.5mm)

-B ...

….… 3.598x2.000x1.299 inches (91.4x50.8x33.0mm)

-C .

….…... 3.598x2.520x1.358 inches (91.4x64.0x34.5mm)

Weight ………………………………………..…… 135g, 170g(-B), 218g(-C)

SAFETY AND EMC:

Emission and Immunity (Ed. 4.0)

………. EN55011 Class B, IEC61000-3-2

IEC61000-4-2, 3, 4, 5, 6, 8, 11, IEC61000-3-3, FCC Part 18 Class B(note 7)

Safety (Ed. 3.1)

……………….. Class Ι, Class II, IEC60601-1, EN60601-1

NOTE:

UL ANSI/AAMI ES60601-1

1. Voltage accuracy is set at full load.

2. Add a 0.1uF ceramic capacitor and a 10uF E.L. capacitor to output for

ripple & noise measuring @20MHz BW.

3. Line regulation is measured from 100Vac to 240Vac with full load.

4. Load regulation is measured from 10% to 100% full load.

5. Typical efficiency at 230 VAC and full load at 25°C.

6. Standard input and output connectors (CN1 and CN2) wafer with

TAIWAN KING PIN TERMINAL PVHI series and mate with JST

housing VHR series or equivalent.

7. Requires 10CFM.

Mechanical Specification

All Dimensions In Inches[mm]

Tolerance

Inches:x.xxx= ± 0.02

Millimeters: x.xx = ± 0.5

1

2

3

4

5

6

PIN CONNECTION

Pin

Function

1

ACL

2

ACN

3

-Vout

4

-Vout

5

+Vout

6

+Vout

0.150 [3.81]

2.700 [68.58]

3.000 [76.20]

Air Flow

Direction

CFM130M

3.354 [85.20]

3.598 [91.40]

3

6

5

4

1

2

Air Flow

Direction

0.150 [3.80]

3.598 [91.40]

2

1

6

4

5

3

Air Flow

Direction

CFM130M-B

CFM130M-C

PE

PE

PE

Typical at 25

℃, nominal line and 75% load, unless otherwise Specified