FS32K112BHTXVLUTR datasheet(4/100 Pages) NXP

4 / 100 page

1 Block diagram

Following figures show superset high level architecture block diagrams of S32K14x,

S32K14xW and S32K11x series respectively. Other devices within the family have a

subset of the features. See Feature comparison for chip specific values.

Mux

Trace

port

Crossbar switch (AXBS-Lite)

eDMA

DMA

MUX

Core

Peripheral bus controller

CRC

WDOG

DSP

NVIC

ITM

FPB

DWT

AWIC

SWJ-DP

TPIU

JTAG &

Serial Wire

Arm Cortex M4F

AHB-AP

PPB

GPIO

Mux

FPU

Clock

SPLL

LPO

128 kHz

Async

512B

TCD

LPIT

LPI2C

FlexIO

Flash memory

controller

Code flash

Data flash

Low Power

Timer

12-bit ADC

TRGMUX

LPUART

LPSPI

FlexCAN

FlexTimer

PDB

generation

LPIT

Peripherals present

on all S32K devices

Peripherals present

on selected S32K devices

Key:

Device architectural IP

on all S32K devices

FIRC

48 MHz

ENET

SAI

SOSC

8-40 MHz

(see the "Feature Comparison"

memory

4-40 MHz

QuadSPI

RTC

CMP

8-bit DAC

SIRC

8 MHz

FlexRAM/

SRAM

1: On this device, NXP’s system MPU implements the safety mechanisms to prevent masters from

accessing restricted memory regions. This system MPU provides memory protection at the

level of the Crossbar Switch. Each Crossbar master (Core, DMA, Ethernet) can be assigned

different access rights to each protected memory region. The Arm M4 core version in this family

does not integrate the Arm Core MPU, which would concurrently monitor only core-initiated memory

accesses. In this document, the term MPU refers to NXP’s system MPU.

2: For the device-specific sizes, see the "On-chip SRAM sizes" table in the "Memories and Memory Interfaces"

chapter of the S32K1xx Series Reference Manual.

section)

ERM

EWM

MCM

Lower region

Upper region

Main SRAM2

Code Cache

EIM

LMEM

controller

LMEM

QSPI

CSEc3

System MPU1

3: CSEc (Security) or EEPROM writes/erase will trigger error flags in HSRUN mode (112 MHz) because this

use case is not allowed to execute simultaneously. The device need to switch to RUN mode (80 MHz) to

execute CSEc (Security) or EEPROM writes/erase.

Figure 1. High-level architecture diagram for the S32K14x and S32K14xW family

Block diagram

S32K1xx Data Sheet, Rev. 12, 02/2020

NXP Semiconductors

FS32K112BHTXVLUTR bảng dữ liệu(PDF) 4 Page - NXP Semiconductors

FS32K112BHTXVLUTR bảng dữ liệu(HTML) 4 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

bảng dữ liệu tải về

Link URL