Accessories

AF-P

Anti-rotation bracket AF/NF.

AV8-25

Shaft extension

IND-AFB

End stop indicator

K7-2

Shaft clamp reversible

KG10A

Ball joint

KG8

Ball joint

KH10

Damper crank arm

KH8

Damper crank arm

KH-AFB

Actuator arm

SH10

Push rod for KG10A ball joint (36” L, 3/8” diameter).

SH8

Push rod for KG6 & KG8 ball joints (36” L, 5/16” diameter).

TOOL-06

8 mm and 10 mm wrench.

ZG-100

Univ. right angle bracket 17”x11-1/8”x6” (HxWxbase).

ZG-101

Univ. right angle bracket 13x11x7-7/16” (HxWxbase).

ZG-109

Right angle bracket for ZS-260.

ZG-110

Stand-off bracket for ZS-260.

ZG-118

AFB(X)/NFB(X) U bracket 5-7/8x5-1/2x2-19/32” (HxWxD).

ZG-120

Jackshaft mounting bracket.

ZG-AFB

Mounting kit for linkage operation

ZG-AFB118 AFB(X)/NFB(X) crankarm adaptor kit.

ZG-DC1

Damper clip for damper blade, 3.5” width.

ZG-DC2

Damper clip for damper blade, 6” width.

ZG-JSA-1

1” diameter jackshaft adaptor (11” L).

ZG-JSA-2

1-5/16” diameter jackshaft adaptor (12” L).

ZG-JSA-3

1.05” diameter jackshaft adaptor (12” L).

ZS-100

Weather shield - galvaneal 13x8x6” (LxWxD).

ZS-101

Base plate for ZS-100.

ZS-150

Weather shield - PC w/ foam seal 16x8-3/8x4” (LxWxD).

ZS-260

Explosion proof housing.

ZS-300

NEMA 4X, 304 stainless steel enclosure.

ZS-300-5

NEMA 4X, 316L stainless steel enclosure.

ZS-300-C1 1/2” shaft adaptor, standard wtih ZS-300(-5).

ZS-300-C2 3/4” shaft adaptor for ZS-300(-5).

ZS-300-C3 1” shaft adaptor for ZS-300(-5).

Z-SF

Base plate extension

P475

Shaft mount, non-Mercury aux. switch for 1/2” dia. shafts.

P475-1

Shaft mount, non-Mercury aux. switch for 1” dia. shafts.

PS-100

Low voltage and control signal simulator.

TF-CC US

Cable conduit connector, 1/2”.

ZG-X40

120 to 24 VAC, 40 VA transformer.

Typical Specification

Spring return control damper actuators shall be direct coupled type which

require no crank arm and linkage and be capable of direct mounting to a

jackshaft up to a 1.05” diameter. The actuator must provide modulating

damper control in response to a 0 to 10 V phasecut control input from an

electronic controller or positioner. The actuators must be designed so that

they may be used for either clockwise or counter clockwise fail-safe operation.

Actuators shall use a brushless DC motor controlled by a microprocessor

and be protected from overload at all angles of rotation. Run time shall be

constant, and independent of torque. A 2 to 10 VDC feedback signal shall be

provided for position feedback or master slave applications. Actuators shall be

cULus listed and have a 5 year warranty, and be manufactured under ISO 9001

International Quality Control Standards. Actuators shall be as manufactured

by Belimo.

Blk (1) Common

Red (2) + Hot

Pnk (6) C1 Input

Org (5) U Output

Control Signal

(+)

0 to 10 V Phasecut

(–)

Feedback Signal (+)

2 to 10 VDC (–)

Line

Volts

1

2

3

24 VAC Transformer

5

Phasecut Control

AFB24-PC Damper Actuator Technical Data Sheet

Modulating, Spring Return, 24 V, 0 to 10 V Phasecut Control Signal

800-543-9038 USA

866-805-7089 CANADA

203-791-8396 LATIN AMERICA / CARIBBEAN