2

1. POWER REQUIREMENTS:

Must use a Class 2 circuit according to National Electrical Code (NEC),

NFPA-70 or Canadian Electrical Code (CEC), Part I, C22.1 or a Limited

Power Supply (LPS) according to IEC 60950-1 or Limited-energy circuit

according to IEC 61010-1.

Power connection via removable three position terminal block.

Supply Voltage:

+24 VDC ±20%

G310C/R

G310S

Typical Power:

16 W

16 W

Maximum Power:

25 W

26 W

Note:

1. The G310’s circuit common is not connected to the enclosure of the

unit. See “Connecting to Earth Ground” in the section “Installing and

Powering the G310.”

2. BATTERY: Lithium coin cell CR2025. Typical lifetime of 10 years.

3. LCD MODULE DISPLAYS:

MODEL

G310C2

G310R2

G310S2

SIZE

10.4-inch

10.4-inch

10.4-inch

TYPE

TFT

TFT

TFT

COLORS

32K

32K

32K

PIXELS

640 X 480

800 X 600

640 X 480

BRIGHTNESS

BACKLIGHT LIFETIME * 70,000 HR typ. 70,000 HR typ. 50,000 HR typ.

BACKLIGHT TYPE

LED

LED

LED

* Lifetime at room temperature. Refer to “Display” in the “Software/Unit

Operation” section.

4. 8-KEY KEYPAD: for on-screen menus.

5. TOUCHSCREEN: Resistive analog

6. MEMORY:

On Board User Memory: 32 Mbyte of onboard non-volatile Flash memory.

Memory Card: CompactFlash Type II slot for Type I and Type II

CompactFlash cards.

7. COMMUNICATIONS:

USB Port: Adheres to USB 2.0 specification full speed only via Type B

connection.

USB Host Ports: Comply with Universal Serial Bus Specification Rev 2.0.

Support data transfers at full-speed. Hardware over current protected (0.5

A max per port).

Serial Ports: Ports are individually isolated. Format and Baud Rates for each

port are individually software programmable up to 115,200 baud.

PGM Port: RS232 port via RJ12.

COMMS Ports: RS422/485 port via RJ45, and RS232 port via RJ12.

Note: For additional information on the communications or signal

common and connections to earth ground please see the “Connecting to

Earth Ground” in the section “Installing and Powering the G310.”

Ethernet Ports: 10 BASE-T / 100 BASE-TX

RJ45 jack is wired as a NIC (Network Interface Card). The jack shield is

electrically connected to Earth ground.

A secondary ethernet port (with its own Mac ID) is available as an option.

8. ENVIRONMENTAL CONDITIONS:

Operating Temperature Range: 0 to 50°C

Storage Temperature Range: -20 to 70°C

Operating and Storage Humidity: 80% maximum relative humidity (non-

condensing) from 0 to 50°C.

Vibration to IEC 68-2-6: Operational 5 to 150 Hz, 2 g.

Shock to IEC 68-2-27: Operational 35 g.

Altitude: Up to 2000 meters.

9. CERTIFICATIONS AND COMPLIANCES:

CE Approved

EN 61326-1 Immunity to Industrial Locations

Emission CISPR 11 Class A

Safety requirements for electrical equipment for measurement, control, and

laboratory use:

EN 61010-1: General Requirements

RoHS Compliant

UL Listed: File #E179259

UL Hazardous: File #E245515

Type 4X Enclosure rating (Face only)

IP66 Enclosure rating (Face only)

10. CONNECTIONS: Compression cage-clamp terminal block.

Wire Gage: 12-30 AWG copper wire

Torque: 5-7 inch-pounds (56-79 N-cm)

11. CONSTRUCTION: Steel rear metal enclosure with NEMA 4X/IP66

aluminum front plate when correctly fitted with the gasket provided.

Installation Category II, Pollution Degree 2.

12. MOUNTING REQUIREMENTS: Maximum panel thickness is 0.25" (6.3

mm). For NEMA 4X/IP66 sealing, a steel panel with a minimum thickness of

0.125" (3.17 mm) is recommended.

Maximum Mounting Stud Torque: 17 inch-pounds (1.92 N-m)

13. WEIGHT: 5.44 lbs (2.47 Kg)

WARNING - DO NOT CONNECT OR DISCONNECT CABLES

WHILE POWER IS APPLIED UNLESS AREA IS KNOWN TO BE

NON-HAZARDOUS. USB PORT IS FOR SYSTEM SET-UP AND

DIAGNOSTICS AND IS NOT INTENDED FOR PERMANENT

CONNECTION.

9.50

(241.3)

12.83 (325.8)

2.45 (62)

11.25 (285.8)

8.25

(209.4)

DIMENSIONS In inches (mm)