| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TMS320VC5506 bảng dữ liệu(PDF) 22 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
TMS320VC5506 bảng dữ liệu(HTML) 22 Page - Texas Instruments |
|
22 / 119 page ![]() Introduction 22 October 2006 − Revised January 2008 SPRS375C Table 2−3. Signal Descriptions (Continued) TERMINAL NAME RESET CONDITION BK‡ FUNCTION I/O/Z† MULTIPLEXED SIGNAL NAME PARALLEL BUS (CONTINUED) C11 O/Z EMIF SDRAM column strobe. The initial state of this pin depends on the GPIO0 pin. GPIO0 = 1: Output, EMIF.SDCAS EMIF.SDCAS O/Z Active-low EMIF SDRAM column strobe. EMIF.SDCAS is selected when the Parallel Port Mode bit field of the External Bus Selection Register is set to 00 or 01. BK EMIF.SDCAS GPIO0 = 0: Reserved C12 O/Z EMIF SDRAM write enable. The initial state of this pin depends on the GPIO0 pin. BK GPIO0 = 1: Output, EMIF.SDWE EMIF.SDWE O/Z EMIF SDRAM write enable. EMIF. SDWE is selected when the Parallel Port Mode bit field of the External Bus Selection Register is set to 00 or 01. BK EMIF.SDWE GPIO0 = 0: Reserved C13 O/Z SDRAM A10 address line. The initial state of this pin depends on the GPIO0 pin. GPIO0 = 1: EMIF.SDA10 O/Z SDRAM A10 address line. Address line/autoprecharge disable for SDRAM memory. Serves as a row address bit (logically equivalent to A12) during ACTV commands and also disables the autoprecharging function of SDRAM during read or write operations. EMIF.SDA10 is selected when the Parallel Port Mode bit field of the External Bus Selection Register is set to 00 or 01. BK GPIO0 = 1: Output, EMIF.SDA10 GPIO0 = 0: Reserved C14 O/Z Memory interface clock for SDRAM. The initial state of this pin depends on the GPIO0 pin. GPIO0 = 1: Output, EMIF.CLKMEM EMIF.CLKMEM O/Z Memory interface clock for SDRAM. EMIF.CLKMEM is selected when the Parallel Port Mode bit field of the External Bus Selection Register is set to 00 or 01. BK EMIF.CLKMEM GPIO0 = 0: Reserved † I = Input, O = Output, S = Supply, Hi-Z = High-impedance ‡ BK = bus keeper (the bus keeper maintains the previous voltage level during reset or while the output pin is not driven), PU = pullup, PD = pulldown, H = hysteresis input buffer, FS = fail-safe buffer |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |