2. Connect the power by removing the selected knockout and installing either 1/2-inch conduit or an AC power cord with

supplied cord grip strain relief. If you are using rigid conduit, the conduit hub/connector must be approved for use in dry or

damp locations and must be connected to the conduit before the hub/connector is connected to the luminaire. The

supplied cord grip diameter range is 4.3 to 11.4 mm.

3. Connect the incoming supply wires to the LED Driver input connectors according to the wiring diagram.

4. Connect the ground wire to the three-position ground connector.

5. If you are using 0–10 V analog dimming, connect to the LED Driver dimming connectors according to the wiring diagram.

6. Attach the red and black wires from the cover LED board to the output connectors on the Driver.

7. Re-attach the cover to the housing by snapping it into place. Secure the cover to the housing by using a minimum of one

self tapping screw on each end of the housing (four screws are provided).

8. Repeat these steps on other end of the luminaire if you are connecting to more than one luminaire in a continuous run.

Wiring Diagram

Diagram

Wire

Connection

N

L

Dim (+)

Dim (-)

N

L

Dim (+)

Dim (-)

L - Black

Line/Hot

N - White

Neutral

- Green/Yellow

Earth ground

Dim (+) - Purple

0–10 V dc analog dimming

Dim (-) - Gray

Return analog dimming

Specifications

Supply Voltage

Nominal voltage: 120 V ac to 277 V ac, 60 Hz in North America

Nominal voltage: 120 V ac to 277 V ac, 50/60 Hz outside North America

Power factor: > 0.95 at 120 V ac and > 0.90 at 277 V ac

Total harmonic distortion (THD): < 20%

See electrical characteristics on product label

Supply Current

Lighted

Length

(mm)

Max.

Current

Draw (A) at

90 V ac

Typical Current Draw (A)

120 V ac

230 V ac

277 V ac

1200

0.850

0.43

0.22

0.18

Supply Protection Circuitry

Protected against transient voltages

LED Lifetime

When operating within specifications, output will decrease less than 30%

after 50,000 hours.

Construction

Galvanized steel with corrosion resistant polyester powder coat,

polycarbonate window and end caps.

Weight: 2.8 kg (6.25 lbs)

Mounting

Compatible with a variety of common mounting and hanging methods.

Housing includes six mounting holes for surface mounting.

Several optional mounting brackets are available (see Accessories)

Connections

1/2-inch trade size conduit knockout in nine locations

Weight

2.8 kg (6.2 lbs)

Environmental Rating

IEC IP20

Operating Temperature

Surface Mount Installation: –40 °C to +50 °C (–40 °F to +122 °F)

85% at +50 °C maximum relative humidity (non-condensing)

Light Characteristics

Daylight White Efficacy: 130 lumens/watt typical at 120 V ac at 25 °C (77 °F)

CRI: 82, typical

Color

Color Temperature (CCT)

Lumens (Typical at 25 °C)

Daylight White

5000 K (±300 K)

6800

Storage Temperature

–40 °C to +70 °C (–40 °F to +158 °F)

Vibration and Mechanical Shock

Vibration: 10 Hz to 55 Hz, 0.5 mm peak-to-peak amplitude per IEC

60068-2-6 (5 minute sweep, 30 minute dwell)

Shock: 5G 11 ms duration, half sine wave per IEC 60068-2-27

Impact: IK07 (IEC 60068-2-75)

WLB72B Industrial LED Light Bar (AC)

P/N 210184 Rev. A

www.bannerengineering.com - Tel: + 1 888 373 6767

3