| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STR720 bảng dữ liệu(PDF) 198 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STR720 bảng dữ liệu(HTML) 198 Page - STMicroelectronics |
|
198 / 401 page ![]() STR720 - BUFFERED SPI (BSPI) 198/401 Bit 1 = Reserved. To be left at 0 level (reset status). Bit 0 = DFIFO: Disable for the FIFO. When this bit is enabled, the FIFO pointers are all reset to zero, the RFE bits are set to zero and therefore the BSPI is set to one location. The data within the FIFO is lost. This bit is reset to zero after a clock cycle. BSPI Control/Status Register 3 (BSPCSR3) Address Offset: 14h Reset value: 0000h This register is used to control the BSPI DMA interface. When the BSPI is receiving da- ta, it will be the source of DMA transfer and system memory will act as destination. Conversely, when the BSPI is in transmit mode, it is sending data to an external source and it will act as DMA destination while system memory will be the source. Bits 15:8 = Reserved. These bits must be always written to ‘0’. Bit 7 = RREQ_EN: Receive REQuest ENable This is the enable bit for the reception DMA request and it flags the DMA controller that an amount of data corresponding at least to the configured reception burst length is available in the BSPI receive FIFO to be transferred. 0 = Receive DMA requests are disabled. 1 = Receive DMA requests are enabled. Bit 6 = TREQ_EN: Transmit REQuest ENable This is the enable bit for the transmission DMA request and it flags the DMA controller that in the BSPI transmit FIFO there is an amount of free locations corresponding at least to the configured transmission burst length. 0 = Transmit DMA requests are disabled. 1 = Transmit DMA requests are enabled. Bits 5:4 = RBURST_LEN[1:0]: Receive BURST LENgth These bits configure the burst length when the BSPI receives data. This programmable length is used to set the number of data words the DMA controller is expected to retrieve upon a receive request; this value is used in the DMA interface to determine when the BSPI is ready to send a data burst to the DMA. A word can be 16 bit or 8 bit wide according to the configuration set in WL bits inside BSPCSR1 register. 15 14 13 12 11 10 9 8 765432 1 0 Reserved RREQ _EN TREQ _EN RBURST_LEN [1:0] TBURST_LEN [1:0] DMA _EN MASK _SS -rw rw rw rw rw rw 1 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |