| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
SN74HCS74-Q1 bảng dữ liệu(PDF) 11 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
SN74HCS74-Q1 bảng dữ liệu(HTML) 11 Page - Texas Instruments |
|
11 / 19 page ![]() Q Q CLR Output R1 PRE R2 C1 VCC D CLK VCC R3 C3 VCC C2 VCC GND 11 SN74HCS74-Q1 www.ti.com SCES894A – APRIL 2019 – REVISED JUNE 2019 Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated 9 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 9.1 Application Information Toggle switches are typically large, mechanically complex and relatively expensive. It is desirable to use a momentary switch instead because they are small, mechanically simple and low cost. Some systems require a toggle switch's functionality but are space or cost constrained and must use a momentary switch instead. The SN74HCS74-Q1 has integrated Schmitt-trigger inputs that eliminate the need for a second IC for signal conditioning, reducing the required board space. This makes the SN74HCS74-Q1 an ideal device for converting a momentary switch into a toggle switch. If the data input (D) of the SN74HCS74-Q1 is tied to the inverted output (Q), then each clock pulse will cause the value at the output (Q) to toggle. The momentary switch can be debounced and directly connected to the clock input (CLK) to toggle the output. 9.2 Typical Application Figure 12. Device Power Button Circuit 9.2.1 Design Requirements The supply voltage of the D-Type flip flop must be chosen to meet the supply voltage specification from the Recommended Operating Conditions. The same supply must be used for the pushbutton and power on reset circuit allowing for the high and low level input voltage conditions, VT+ and VT–, to meet the requirements in Electrical Characteristics. When the flip-flop is first powered on, it will start in an unknown state if both the (PRE) and (CLR) pins are directly tied high. However, if either the (PRE) or (CLR) pin is held low, then flip-flop will be in a known state. With the SN74HCS74-Q1, a power on reset circuit only requires a resistor (R) and capacitor (C) to create a delay. The R and C values create a delay that is approximately 2.2×RC. An additional Schmitt-trigger input device would be required to allow this slow rise if the flip-flop did not have Schmitt-trigger inputs. In this application, it is desired to have the output (Q) in the LOW state at startup, so R3 and C3 are connected directly to the CLR pin, as shown in Figure 12. |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |