| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STR-A6000MZ bảng dữ liệu(PDF) 15 Page - Sanken electric |
|
|
|||||||||||||||||||||||||||||
STR-A6000MZ bảng dữ liệu(HTML) 15 Page - Sanken electric |
|
15 / 26 page ![]() STR-A6000MZ/HZ Series STR-A6000MZ/HZ - DS Rev.1.2 SANKEN ELECTRIC CO.,LTD. 15 Mar.13, 2015 9.9.1 DC Line Detection Figure 9-12 shows the BR pin peripheral circuit of DC line detection. There is a ripple voltage on C1 occurring at a half period of AC cycle. In order to detect each peak of the ripple voltage, the time constant of RC and C4 should be shorter than a half period of AC cycle. Since the cycle of the ripple voltage is shorter than tOLP, the switching operation does not stop when only the bottom part of the ripple voltage becomes lower than VBR(OUT). Thus it minimizes the influence of load conditions on the voltage detection. The components around the BR pin: ・ R A and RB are a few megohms. Because of high voltage applied and high resistance, it is recommended to select a resistor designed against electromigration or use a combination of resistors in series for that to reduce each applied voltage, according to the requirement of the application. ・ R C is a few hundred kilohms ・ C4 is 470 pF to 2200 pF for high frequency noise reduction VDC U1 BR 2 C4 RC GND 3 RB RA VAC BR1 C1 Figure 9-12 DC line detection Neglecting the effect of both input resistance and forward voltage of rectifier diode, the reference value of C1 voltage when the Brown-In and Brown-Out Function is activated is calculated as follows: C B A ) TH ( BR ) OP ( DC R R R 1 V V (3) where, VDC(OP) : C1 voltage when the Brown-In and Brown-Out Function is activated VBR(TH) : Any one of threshold voltage of the BR pin (see Table 9-1) Table 9-1 BR pin threshold voltage Parameter Symbol Value (Typ.) Brown-In Threshold Voltage VBR(IN) 5.60 V Brown-Out Threshold Voltage VBR(OUT) 4.80 V VDC(OP) can be expressed as the effective value of AC input voltage using Equation (4). ) OP ( DC RMS ) OP ( AC V 2 1 V (4) RA, RB, RC and C4 should be selected based on actual operation in the application. 9.9.2 AC Line Detection Figure 9-13 shows the BR pin peripheral circuit of AC line detection. In order to detect the AC input voltage, the time constant of RC and C4 should be longer than the period of AC cycle. Thus the response of the BR pin detection becomes slow compared with the DC line detection. This method detects the AC input voltage, and thus it minimizes the influence from load conditions. Also, this method is free of influence from C1 charging and discharging time. VDC U1 BR 2 C4 RC GND 3 RB RA VAC BR1 C1 VCC 3 RS Figure 9-13 AC line detection The components around the BR pin: ・ R A and RB are a few megohms. Because of high voltage applied and high resistance, it is recommended to select a resistor designed against electromigration or use a combination of resistors in series for that to reduce each applied voltage, according to the requirement of the application. ・ R C is a few hundred kilohms ・ R S must be adjusted so that the BR pin voltage is more than VBR(DIS) = 0.6 V when the VCC pin voltage is VCC(OFF) = 8.5 V ・ C4 is 0.22 μF to 1 μF for averaging AC input voltage and high frequency noise reduction |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |