GD25LE80CSJG datasheet(24/68 Pages) GIGADEVICE

24 / 68 page

1.8V Uniform Sector

Dual and Quad Serial Flash

GD25LE80C

Quad I/O Fast Read with “8/16/32/64-Byte Wrap Around” in Standard SPI mode

The

Quad I/O Fast Read command can be used to access a specific portion within a page by issuing “Set Burst with Wrap”

(77H) commands prior to EBH.

The “Set Burst with Wrap” (77H) command can either enable or disable the “Wrap Around”

feature for the following EBH commands. When “Wrap Around” is enabled, the data being accessed can be limited to either

an 8/16/32/64-Byte section of a 256-Byte page. The output data starts at the initial address specified in the command, once

it reaches the ending boundary of the 8/16/32/64-Byte section, the output will wrap around the beginning boundary

automatically until CS# is pulled high to terminate the command.

The Burst with Wrap feature allows applications that use cache to quickly fetch a critical address and then fill the cache

afterwards within a fixed length (8/16/32/64-Byte

) of data without issuing multiple read commands. The “Set Burst with Wrap”

command allows three “Wrap Bits” W6-W4 to be set. The W4 bit is used to enable or disable the “Wrap Around” operation

while W6-W5 is used to specify the length of the wrap around section within a page.

7.12 Set Burst with Wrap (77H)

The Set Burst with Wrap command is used in conjunction with “Quad I/O Fast Read” command to access a fixed length of

8/16/32/64-Byte section within a 256-Byte page, in standard SPI mode.

The Set Burst with Wrap command sequence: CS# goes low  Send Set Burst with Wrap command  Send 24 dummy

bits 

Send 8 bits “Wrap bits”  CS# goes high.

W6,W5

W4=0

W4=1 (default)

Wrap Around

Wrap Length

Wrap Around

Wrap Length

0, 0

Yes

8-Byte

N/A

0, 1

Yes

16-Byte

N/A

1, 0

Yes

32-Byte

N/A

1, 1

Yes

64-Byte

N/A

If the W6-W4 bits are set by the

Set Burst with Wrap command, all the following “Quad I/O Fast Read” command will use

the W6-W4 setting to access the 8/16/32/64-Byte

section within any page. To exit the “Wrap Around” function and return to

normal read operation, another Set Burst with Wrap command should be issued to set W4=1.

Figure 15. Set Burst with Wrap Sequence Diagram

Command

77H

CS#

SCLK

SI(IO0)

SO(IO1)

9 10 11 12 13 14 15

W6-W4

WP#(IO2)

HOLD#(IO3)

GD25LE80CSJG bảng dữ liệu(PDF) 24 Page - GigaDevice Semiconductor (Beijing) Inc.

GD25LE80CSJG bảng dữ liệu(HTML) 24 Page - GigaDevice Semiconductor (Beijing) Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

bảng dữ liệu tải về

Link URL