DLP2010AFQJ datasheet(39/42 Pages) TI1

39 / 42 page

SECTION A-A

NOTCH OFFSETS

DWG NO.

INV11-2006a

2512515

TITLE

SIZE

DWG NO

REV

SCALE

SHEET

DATE

ENGINEER

QA/CE

APPROVED

DRAWN

INSTRUMENTS

Dallas Texas

APPLICATION

NEXT ASSY

USED ON

THIRD ANGLE

PROJECTION

TEXAS

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN MILLIMETERS

TOLERANCES:

ANGLES

1

2 PLACE DECIMALS

0.25

1 PLACE DECIMALS

0.50

DIMENSIONAL LIMITS APPLY BEFORE PROCESSES

INTERPRET DIMENSIONS IN ACCORDANCE WITH ASME

Y14.5M-1994

REMOVE ALL BURRS AND SHARP EDGES

PARENTHETICAL INFORMATION FOR REFERENCE ONLY

ICD, MECHANICAL, DMD,

.2 WVGA SERIES 244

2512515

9/14/2012

20:1

P. KONRAD

F. ARMSTRONG

M. SOUCEK

9/26/2012

9/18/2012

9/14/2012

0314DA

B. HASKETT

NOTES UNLESS OTHERWISE SPECIFIED:

REVISIONS

B. HASKETT

M. DORAK

9/18/2012

REV

DESCRIPTION

DATE

ECO 2127544: INITIAL RELEASE

9/14/2012

BMH

ECO 2129552: ENLARGE APERTURE ON RIGHT SIDE;

MOVE ACTIVE ARRAY Y-LOCATION DIM, SH. 3

12/10/2012

BMH

ECO 2131252: ENLARGE APERTURE ALONG BOTTOM EDGE

2/20/2013

BMH

ECO 2135244: CORRECT WINDOW THK TOL, ZONE B6

8/5/2013

BMH

ECO 2138016: INCREASE WINDOW THK NOMINAL

11/21/2013

BMH

2.65 - 0.1

0.2

1.176

0.05

0.78

0.063

1.003

0.077

0.7

0.05

(1.783)

A 3 SURFACES INDICATED

IN VIEW B (SHEET 2)

DIE PARALLELISM TOLERANCE APPLIES TO DMD ACTIVE ARRAY ONLY.

ROTATION ANGLE OF DMD ACTIVE ARRAY IS A REFINEMENT OF THE LOCATION

TOLERANCE AND HAS A MAXIMUM ALLOWED VALUE OF 0.6 DEGREES.

BOUNDARY MIRRORS SURROUNDING THE DMD ACTIVE ARRAY.

DMD MARKING TO APPEAR IN CONNECTOR RECESS.

NOTCH DIMENSIONS ARE DEFINED BY UPPERMOST LAYERS OF CERAMIC,

AS SHOWN IN SECTION A-A.

ENCAPSULANT TO BE CONTAINED WITHIN DIMENSIONS SHOWN IN VIEW C

(SHEET 2). NO ENCAPSULANT IS ALLOWED ON TOP OF THE WINDOW.

ENCAPSULANT NOT TO EXCEED THE HEIGHT OF THE WINDOW.

DATUM B IS DEFINED BY A DIA. 2.5 PIN, WITH A FLAT ON THE SIDE FACING

TOWARD THE CENTER OF THE ACTIVE ARRAY, AS SHOWN IN VIEW B (SHEET 2).

WHILE ONLY THE THREE DATUM A TARGET AREAS A1, A2, AND A3 ARE USED

FOR MEASUREMENT, ALL 4 CORNERS SHOULD BE CONTACTED, INCLUDING E1,

TO SUPPORT MECHANICAL LOADS.

(ILLUMINATION

DIRECTION)

ACTIVE ARRAY

0.038 A

 0.02D

(PANASONIC AXT640124DD1, 40-CONTACT, 0.4 mm

PITCH BOARD-TO-BOARD CONNECTOR HEADER)

MATES WITH PANASONIC AXT540124DD1 OR EQUIVALENT

CONNECTOR SOCKET

(SHEET 3)

(

2.5)

2X ENCAPSULANT

(0.88)

(2.5)

90°

1°

5.3 - 0.1

0.3

15.9 - 0.1

0.3

0.8 - 0.1

0.2

14.1

0.08

(1)

1.4 - 0.1

0.2

2.5

0.075

0.4

0.1

4X (R0.2)

1.4

0.1

 0.05

1.25 5

0.4 MIN

TYP.

(1.4)

0 MIN TYP.

(OFF-STATE

DIRECTION)

DLP2010AFQJ bảng dữ liệu(PDF) 39 Page - Texas Instruments

DLP2010AFQJ bảng dữ liệu(HTML) 39 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

bảng dữ liệu tải về

Link URL