Switch mode Power Supply

S82K

L-9

3- to 240-W models without PFC

Note: 1. Defined with a 100% load and the rated input voltage (100 or 200 VAC).

2. Do not press down on the terminal block with a force exceeding 75 N while tightening the terminals.

3. To ensure the emission ratings, a noise filter should be used on the output lines at the closest point.

(3- to 50-W models: S82Y-JF3-N, 90- and 100-W models: S82Y-JF6-N)

4. Models other than dual output models satisfy the Class-2 requirements.

5. To meet Class-2 requirements with the 100-W model, either a fuse or circuit breaker that is UL listed or CSA certified, and rated at 4.2 A

max. should be wired in series with the load to be connected to the power supply. Only then can the power supply output be considered

as meeting Class 2.

Item

Single output

Dual

outputs

Single output

3 W

7.5 W

7.5 W

15 W

30 W

50 W

90 W

100 W

240 W

Other

Ambient temperature Operating: See the derating curve in the Engineering Data section

(no condensation or icing)

Storage:

−25°C to 65°C (no condensation or icing)

Ambient humidity

Operating: 25% to 85%

Storage:

25% to 90%

Dielectric strength

3,000 VAC at 50/60 Hz for 1 min (between all inputs and outputs)

2,000 VAC at 50/60 Hz for 1 min (between all inputs and GR terminal)

1,000 VAC at 50/60 Hz for 1 min (between all outputs and GR terminal)

Alarm current: 10 mA (3- to 7.5-W models) 20 mA (15- to 100-W models) 25 mA (240-W models)

Insulation resistance 100 M

Ω min. at 500 VDC (between all outputs and all inputs/GR terminal)

Vibration resistance

Malfunction: 10 to 55 Hz, 0.375-mm single amplitude for 2 hrs each in X, Y, and

Z directions

Malfunction: 10 to

55 Hz, 0.15-mm

single amplitude

for 2 hrs each in X,

Y, and Z directions

Shock resistance

±X, ±Y, and ±Z directions

Screw tightening

torque

0.74 N • m max. (see note 2)

Output indicator

Yes (green)

Electromagnetic

interference

(see note 1)

Conforms to FCC class B

Conforms to FCC class A

EMC

(see note 3)

3 to 100-W Models

(EMI):

EN50081-1

Emission Enclosure:

EN55022 class B (equivalent to EN55011 class B)

Emission AC Mains:

EN55022 class B (equivalent to EN55011 class B)

Emission Output Ports: EN55022 class A (with a recommended optional filter) (see note 3)

240-W Models

(EMI):

EN50081-2

Emission Enclosure:

EN55011 class A

Emission AC Mains:

EN55011 class A

Common to All Models

(EMS):

EN50082-2

Immunity ESD:

EN61000-4-2: 4-kV contact discharge (level 2)

8-kV air discharge (level 3)

Immunity Burst:

EN61000-4-4: 2-kV power-line (level 3)

2-kV output line (level 4)

Immunity Surge:

EN61000-4-5: between 2-kV lines (except for 240-W models)

between 4-kV line and FG (except for 240-W models)

Approved standards

Class 2 (UL 1310)/Class 2 (CSA C22.2 No. 950) (see notes 4 and 5)

UL 508 (Listing)/1950

CSA C22.2 No.14/No.950, EN50178 (VDE0160), EN60950

Conforms to VDE0106/P100

UL 508 (Listing)/

1012

CSA C22.2 No.14,

CSA E.B. 1402C,

EN50178

(VDE0160),

EN60950

Conforms to

VDE0106/P100

Weight

150 g max.

260 g

max.

380 g

max.

400 g

max.

600 g max.

1,800 g max.