MXD2020GL datasheet(2/7 Pages) ETC

2 / 7 page

MEMSIC MXD2020GL/ML/NL/HL

Page 2 of 7

2002.08.29.1

MXD2020GL/HL/ML/NL SPECIFICATIONS (Measurements @ 25°C, Acceleration = 0 g unless otherwise noted; VDD, VDA = 5.0V

unless otherwise specified)

Parameter

Conditions

Min

MXD2020G/HL

Typ

Max

Min

MXD2020M/NL

Typ

Max

Units

SENSOR INPUT

Measurement Range1

Each Axis

±1.0

Nonlinearity

Best fit straight line

0.5

% of FS

Alignment Error2

X Sensor to Y Sensor

±1.0

degrees

Transverse Sensitivity3

±2.0

SENSITIVITY

Sensitivity, Digital Outputs at

pins

DOUTX and DOUTY

4 Change

Each Axis

% duty

cycle/g

over Temperature

-10

-25

ZERO g BIAS LEVEL

0 g Offset4

Each Axis

-0.1

0.0

+0.1

-0.1

0.0

+0.1

0 g Duty Cycle4

% duty

cycle

0 g Offset over Temperature

Based on 20%/g

±1.5

±0.03

±1.5

±0.03

mg/

°C

NOISE PERFORMANCE

Noise Density, rms

0.2

0.4

0.2

0.4

mg/

FREQUENCY RESPONSE

3dB Bandwidth

TEMPERATURE OUTPUT

Tout Voltage

1.21

1.25

1.29

1.21

1.25

1.29

Sensitivity

4.6

5.0

5.4

4.6

5.0

5.4

mV/

°K

VOLTAGE REFERENCE

VRef

@3.0V-5.0V supply

2.4

2.5

2.65

2.4

2.5

2.65

Change over Temperature

0.1

mV/

°C

Current Drive Capability

Source

100

µA

SELF TEST

Continuous Voltage at DOUTX,

DOUTY under Failure

@5.0V Supply, output

rails to

supply voltage

5.0

Continuous Voltage at DOUTX,

DOUTY under Failure

@3.0V Supply, output

rails to

supply voltage

3.0

DOUTX and DOUTY OUTPUTS

Normal Output Range

@5.0V Supply

@3.0V Supply

0.1

4.9

2.9

0.1

4.9

2.9

Current

Source or sink, @

3.0V-5.0V supply

100

µA

Rise/Fall Time

3.0 to 5.0V supply

100

110

100

110

Turn-On Time

@5.0V Supply

@3.0V Supply

100

POWER SUPPLY

Operating Voltage Range

3.0

5.25

3.0

5.25

Supply Current

@ 5.0V

2.7

3.8

4.4

2.7

3.8

4.4

Supply Current4

@ 3.0V

3.2

4.7

5.4

3.2

4.7

5.4

TEMPERATURE RANGE

Operating Range

+70

-40

+105

°C

NOTES

1 Guaranteed by measurement of initial offset and sensitivity.

2 Alignment error is specified as the angle between the true and indicated axis of

sensitivity.

3 Transverse sensitivity is the algebraic sum of the alignment and the inherent

sensitivity errors.

4 The device operates over a 3.0V to 5.25V supply range. Please note that sensitivity

and zero g bias level will be slightly different at 3.0V operation. For devices to be

operated at 3.0V in production, they can be trimmed at the factory specifically for

this lower supply voltage operation, in which case the sensitivity and zero g bias

level specifications on this page will be met. Please contact the factory for specially

trimmed devices for low supply voltage operation.

MXD2020GL bảng dữ liệu(PDF) 2 Page - List of Unclassifed Manufacturers

MXD2020GL bảng dữ liệu(HTML) 2 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7

bảng dữ liệu tải về

Link URL