ICL7663SCBA datasheet(3/8 Pages) RENESAS

3 / 8 page

ICL7663S

FN3180 Rev 6.00

Page 3 of 8

October 2, 2015

Absolute Maximum Ratings

Thermal Information

Input Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+18V

Any Input or Output Voltage (Note 1)

Terminals 1, 2, 3, 5, 6, 7 . . . . . . . . . . . . . VIN+ 0.3V to GND -0.3V

Output Source Current

Terminal 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA

Terminal 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25mA

Output Sinking Current

Terminal 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10mA

Operating Conditions

Temperature Range

ICL7663SC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C

ICL7663SI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-25°C to 85°C

Thermal Resistance (Typical, Note 2)

JA (°C/W) JC (°C/W)

CERDIP Package. . . . . . . . . . . . . . . . .

115

PDIP Package* . . . . . . . . . . . . . . . . . .

150

N/A

Plastic SOIC Package . . . . . . . . . . . . .

180

N/A

Maximum Junction Temperature

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C

CERDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175°C

Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C

(SOIC - Lead Tips Only)

*Pb-free PDIPs can be used for through hole wave solder processing

only. They are not intended for use in Reflow solder processing

applications.

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

1. Connecting any terminal to voltages greater than (V+IN + 0.3V) or less than (GND - 0.3V) may cause destructive device latch-up. It is

recommended that no inputs from sources operating on external power supplies be applied prior to ICL7663S power-up.

JA is measured with the component mounted on an evaluation PC board in free air.

Electrical Specifications

Specifications Below Applicable to Both ICL7663S and ICL7663SA, Unless Otherwise Specified. V+IN = 9V,

VOUT = 5V, TA = 25°C, Unless Otherwise Specified. Notes 4, 5. See Test Circuit, Figure 7

PARAMETER

SYMBOL

TEST CONDITIONS

MIN

TYP

MAX

UNITS

Input Voltage

V+IN

ICL7663S

TA = 25°C

1.5

0°C < TA < 70°C

1.6

-25°C < TA < 85°C

1.6

ICL7663SA

0°C < TA < 70°C

1.6

-25°C < TA < 85°C

1.6

Quiescent Current

1.4V

 VOUT  8.5V, No Load

V+IN = 9V

0°C < TA < 70°C

A

-25°C < TA < 85°C

A

V+IN = 16V

0°C < TA < 70°C

A

-25°C < TA < 85°C

A

Reference Voltage

VSET

IOUT1 = 100A, VOUT = VSET

ICL7663S

TA = 25°C

1.2

1.3

1.4

ICL7663SA

TA = 25°C

1.275

1.29

1.305

Temperature

Coefficient

VSET

T

0°C < TA < 70°C

100

ppm

-25°C < TA < 85°C

100

ppm

Line Regulation

VSET

VSET’ VIN

2V < VIN < 15V

0°C < TA < 70°C

0.03

%/V

-25°C < TA < 85°C

0.03

0.3

%/V

VSET Input Current

ISET

0°C < TA < 70°C

0.01

-25°C < TA < 85°C

0.01

Shutdown Input Current

ISHDN

0.01

Shutdown Input Voltage

VSHDN

VSHDN HI: Both VOUT Disabled

1.4

VSHDN LO: Both VOUT Enable

0.3

Sense Pin Input Current

ISENSE

-0.01

ICL7663SCBA bảng dữ liệu(PDF) 3 Page - Renesas Technology Corp

ICL7663SCBA bảng dữ liệu(HTML) 3 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8

bảng dữ liệu tải về

Link URL