HIP6301VCB datasheet(7/20 Pages) RENESAS

7 / 20 page

HIP6301V, HIP6302V

FN9034 Rev 3.00

Page 7 of 20

May 5, 2008

Absolute Maximum Ratings

Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+7V

Input, Output, or I/O Voltage . . . . . . . . . . GND -0.3V to VCC + 0.3V

Recommended Operating Conditions

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±5%

Ambient Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C

Thermal Information

Thermal Resistance (Typical, Note 1)

JA (°C/W)

16 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .

20 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C

Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C

Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and

result in failures not covered by warranty..

NOTES:

JA is measured with the component mounted on a high effective thermal conductivity test board in free air. (See Tech Brief TB379 for details.)

2. VID input levels above 2.9V may produce an reference-voltage offset inaccuracy.

3. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested.

Electrical Specifications

Operating Conditions: VCC = 5V, TA = +0°C to +70°C, Unless Otherwise Specified.

PARAMETER

TEST CONDITIONS

MIN

(Note 3)

TYP

MAX

(Note 3) UNITS

INPUT SUPPLY POWER

Input Supply Current

RT = 100k

POR (Power-On Reset) Threshold

VCC Rising

4.25

4.38

4.5

VCC Falling

3.75

3.88

4.00

REFERENCE AND DAC

System Accuracy

Percent system deviation from programmed VID Codes

-0.8

0.8

DAC (VID0 - VID3) Input Low Voltage DAC Programming Input Low Threshold Voltage

0.8

DAC (VID0 - VID3) Input High Voltage DAC Programming Input High Threshold Voltage

2.0

VID Pull-Up

VIDx = 0V or VIDx = 2.5V (Note 2); Not tested - for reference only

µA

CHANNEL GENERATOR

Frequency, FSW

RT = 100k, ±1%

224

280

336

kHz

Disable Voltage

VFS/DIS to disable controller; Not tested - for reference, only

1.0

ERROR AMPLIFIER

DC Gain

RL = 10k to ground

Gain-Bandwidth Product

CL = 100pF, RL = 10k to ground

MHz

Slew Rate

CL = 100pF, RL = 10k to ground

5.3

V/µs

Maximum Output Voltage

RL = 10k to ground

3.6

Minimum Output Voltage

RL = 10k to ground

0.5

ISEN

Full-Scale Current Level

Not tested - for reference, only

µA

Overcurrent Trip Level

Not tested - for reference, only

82.5

µA

POWER-GOOD MONITOR

Undervoltage Threshold

VSEN Rising

0.92

VDAC

Undervoltage Threshold

VSEN Falling

0.90

VDAC

PGOOD Low Output Voltage

IPGOOD = 4mA

0.4

PROTECTION

Overvoltage Threshold

VSEN Rising

1.12

1.15

1.20

VDAC

Overvoltage Hysteresis

VSEN Falling; Not tested - for reference, only

HIP6301VCB bảng dữ liệu(PDF) 7 Page - Renesas Technology Corp

HIP6301VCB bảng dữ liệu(HTML) 7 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

bảng dữ liệu tải về

Link URL