ICL7667CBA datasheet(2/11 Pages) RENESAS

2 / 11 page

ICL7667

FN2853 Rev 7.00

Page 2 of 11

September 4, 2015

Absolute Maximum Ratings

Thermal Information

Supply Voltage V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±18V

Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . V- -0.3V to V+ +0.3V

Package Dissipation, TA +25°C . . . . . . . . . . . . . . . . . . . . . . .500mW

Operating Conditions

ICL7667C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0° to +70°C

Supply Voltages: V+ = +4.5V to +15V; V- = Ground to -15V

Logic Inputs: Logic Low = V- < Vin < 0.8V ; Logic High = 2.0V< Vin <

V+

Thermal Resistance (Typical, Note 1, 2)

JA (°C/W) JC(°C/W)

8 Ld PDIP Package . . . . . . . . . . . . . . .

150

N/A

8 Ld SOIC Package . . . . . . . . . . . . . . .

170

N/A

Maximum Storage Temperature Range . . . . . . . . . . . -65° to +150°C

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C

(SOIC - Lead Tips Only)

Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

Pb-free PDIPs can be used for through hole wave solder processing

only. They are not intended for use in Reflow solder processing

applications.

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and

result in failures not covered by warranty.

NOTES:

JA is measured with the component mounted on an evaluation PC board in free air.

2. For

JC, the “case temp” location is the center of the exposed metal pad on the package underside.

Electrical Specifications

Parameters with MIN and/or MAX limits are 100% tested at +25°C, V+ = 0V unless otherwise specified.

Temperature limits established by characterization and are not production tested.

PARAMETER

SYMBOL

TEST CONDITIONS

ICL7667C, M

ICL7667M

UNITS

TA = +25°C

0°C

TA  +70°C

MIN

TYP

MAX

MIN

TYP

MAX

DC SPECIFICATIONS

Logic 1 Input Voltage

VIH

V+ = 4.5V

2.0

Logic 1 Input Voltage

VIH

V+V+ = 15V

2.0

Logic 0 Input Voltage

VIL

V+ = 4.5V

0.8

0.5

Logic 0 Input Voltage

VIL

V+ = 15V

0.8

0.5

Input Current

IIL

V+ = 15V, VIN = 0V and 15V

-0.1

0.1

-0.1

0.1

µA

Output Voltage High

VOH

V+ = 4.5V and 15V

V+ -0.05

V+

V+ -0.1

V+

Output Voltage Low

VOL

V+ = 4.5V and 15V

0.05

0.1

Output Resistance

ROUT

VIN = VIL, IOUT = -10mA, V+ = 15V



Output Resistance

ROUT

VIN = VIH, IOUT = 10mA, V+ = 15V



Power Supply Current

ICC

V+ = 15V, VIN = 3V both inputs

Power Supply Current

ICC

V+ = 15V, VIN = 0V both inputs

150

400

µA

SWITCHING SPECIFICATIONS

Delay Time

TD2

(Figure 3)

Rise Time

(Figure 3)

Fall Time

(Figure 3)

Delay Time

TD1

(Figure 3)

ICL7667CBA bảng dữ liệu(PDF) 2 Page - Renesas Technology Corp

ICL7667CBA bảng dữ liệu(HTML) 2 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11

bảng dữ liệu tải về

Link URL