SIP2213 datasheet(2/9 Pages) VISHAY

2 / 9 page

SiP2213

Vishay Siliconix

New Product

www.vishay.com

Document Number: 73190

S-50922—Rev. C, 09-May-05

ABSOLUTE MAXIMUM RATINGS

VIN, VEN, to GND

−0.3 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power Dissipation

MLP33-10 PowerPAKb

1600 mW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MLP44-16 PowerPAKc

1880 mW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage Temperature

−55 to 150_C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Thermal Resistance

MLP33-10 PowerPAKa

50 _C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MLP44-16 PowerPAKa

43 _C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Notes:

Device mounted with all leads soldered or welded to PC board.

Derate 20 mW/_C above 70_C

Derate 23.5 mW/_C above 70_C

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation

of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect device reliability.

RECOMMENDED OPERATING RANGE

Input Voltage Range

2.25 V to 5.5 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Enable Voltage Range

0 V to 5.5 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Temperature Range TA

−40 to 85_C

. . . . . . . . . . . . . . . . . . . . . . . .

Operating Temperature Range TJ

−40 to 125_C

. . . . . . . . . . . . . . . . . . . . . . .

SPECIFICATIONS

Test Conditions Unless Specified

Limits

Parameter

Symbol

VIN = VOUT + 1 Vf, COUT = 1 mF, IOUT = 100 mA, TA = 25_C

Tempa

Minb

Typc Maxb

Unit

Regulators

Output Voltage Accuracy

From Nominal VOUT

Room

−1

Output Voltage Accuracy

Full

−2

Output Voltage

Temperature Coefficient

Room

ppm/_C

Line Regulationf

VIN = VOUT + 1 V to 5 5 V

Room

−0.3

0.2

0.3

Line Regulationf

VIN = VOUT + 1 V to 5.5 V

Full

−0.6

0.6

Load Regulation

IOUT = 100 mA to 150 mA (LDO 1 and 2)

Room

0.2

1.0

Load Regulation

IOUT = 100 mA to 300 mA (LDO 2)

Room

1.5

IOUT = 150 mA (LDO 1 and 2)

Room

120

190

Dropout Voltageg

VDROP

IOUT = 150 mA (LDO 1 and 2)

Full

250

Dropout Voltageg

VDROP

IOUT = 300 mA (LDO 2)

Room

240

340

IOUT = 300 mA (LDO 2)

Full

420

IOUT1 = IOUT2 = 0 mA

Room

Ground Pin Current

IOUT1 = IOUT2 = 0 mA

Full

Ground Pin Current

IOUT1 = 150 mA, IOUT2 = 300 mA

Room

VEN t 0.4 V

Full

2.0

Sequence Time Delayd

tSEQ

Room

Output Voltage Noise

CBP = 0.01 mF

mVrms

Ripple Rejection

f = 1 kHz, COUT = 1 mF, CBP = 10 nF

Room

Ripple Rejection

f = 20 kHz, COUT = 1 mF, CBP = 10 nF

Room

Inputs

EN SW Input Voltage

VIL

Logic Low

Full

0.6

EN, SW Input Voltage

VIH

Logic High

Full

1.8

EN SW Input Current

IIL

VIL t 0.6 V

Room

−1

0.01

EN, SW Input Current

IIH

VIH u 1.8 V

Room

−1

0.01

SET Pin Threshold Voltage

VTH(set)

POR = High

Room

1.25

SET Pin Current Source

VSET = 0 V

Room

0.75

1.25

1.75

Power On Reset (POR) Output

Threshold

VTHL

% of Nominal VOUT2

Room

Threshold

VTHH

% of Nominal VOUT2

Room

Output Voltage

VOL

IL = 250 mA

Room

0.02

0.1

Leakage Current

IPOR

POR = High

Room

−1

0.01

Driver (DRV) Output

Output Voltage

VOL

IL = 150 mA

Full

0.2

0.6

Leakage Current

IDRV = 0 mA, VDRV = 5.5 V, SW = 0 V

Room

−1

0.01

SIP2213 bảng dữ liệu(PDF) 2 Page - Vishay Siliconix

SIP2213 bảng dữ liệu(HTML) 2 Page - Vishay Siliconix

Html Pages

1 2 3 4 5 6 7 8 9

bảng dữ liệu tải về

Link URL