| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
EMC6D103 bảng dữ liệu(PDF) 76 Page - SMSC Corporation |
|
|
|||||||||||||||||||||||||||||
EMC6D103 bảng dữ liệu(HTML) 76 Page - SMSC Corporation |
|
76 / 89 page ![]() Fan Control Device with High Frequency PWM Support and Hardware Monitoring Features Datasheet Revision 0.4 (04-04-05) 76 SMSC EMC6D103 DATASHEET Bit[1] PWM2/INT# pin select: 0=PWM, 1=INT# Bit[2] Reserved Bit[3] TRDY: Temperature Reading Ready. This bit indicates that the temperature reading registers have valid values. This bit is used after writing the start bit to ‘1’. 0= not valid, 1=valid. Bit[4] SUREN: Spin-up reduction enable. This bit enables the reduction of the spin-up time based on feedback from all fan tachometers associated with each PWM. 0=disable, 1=enable (default) Bit[5] SMSC Reserved This is an SMSC Reserved bit. Writing this bit to a value different than the default value may cause unwanted results. Bit[6] SMSC Reserved This is an SMSC Reserved bit. Writing this bit to a value different than the default value may cause unwanted results. Bit[7] Initialization Setting the INIT bit to ‘1’ performs a soft reset. This bit is self-clearing. Soft Reset sets all the registers except the Reading Registers to their default values. 8.2.28 Register 80h: Interrupt Enable 2 Register These registers become read only when the Lock bit is set. Any further attempts to write to these registers shall have no effect. This register is used to enable individual fan tach error events to set the corresponding status bits in the interrupt status registers. This register also contains the group fan tach enable bit (Bit[0] TACH), which is used to enable fan tach events to force the interrupt pin (INT#) low if interrupts are enabled (see Bit[2] INTEN of the Special Function register at offset 7Ch). This register contains the following bits: Bit[0] TACH (Group TACH Enable) 0=Out-of-limit tachometer readings do not affect the state of the INT# pin (default) 1=Enable out-of-limit tachometer readings to make the INT# pin active low Bit[1] Fan Tach 1 Event Enable Bit[2] Fan Tach 2 Event Enable Bit[3] Fan Tach 3 Event Enable Bit[4] Fan Tach 4 Event Enable Bit[5] Reserved Bit[6] Reserved Bit[7] Reserved Table 8.46 Register 80h: Interrupt Enable 2 Register Register Address Read/ Write Register Name Bit 7 (MSb) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSb) Default Value 80h R/W Interrupt Enable 2 (Fan Tachs) RES RES RES TACH4 TACH3 TACH2 TACH1 TACH 1Eh |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |