1 Features
• AEC-Q100 Grade 1 qualified for automotive
applications
• Core
– Arm® 32-bit Cortex®-M0+ CPU with memory
protection unit, frequency up to 32MHz
• Operating characteristics
– Extended temperature: –40°C up to 125°C
– Wide supply voltage range: 1.62V to 3.6V
• Memories
– Up to 64KB of flash memory
– 8KB of SRAM
• High-performance analog peripherals
– 12-bit 1.6 Msps analog-to-digital converter
(ADC), up to 27 external channels
– Configurable 1.4V or 2.5V internal shared
voltage reference (VREF)
– Comparator (COMP) with 8-bit reference DAC
– Integrated temperature sensor
• Optimized low-power modes
– RUN: 93μA/MHz (CoreMark)
– STANDBY 2μA and SRAM and registers fully
retained
– SHUTDOWN: 63nA with I/O wake-up
• Intelligent digital peripherals
– 3-channel DMA controller
– 7-channel event fabric signaling system
– Five timers supporting up to 18 PWM outputs,
all operational down to STANDBY mode
• One 16-bit advanced timer with deadband
and the timer frequency up to 64Mhz
• One 16-bit general purpose timer with 4
capture/compares
• Three 16-bit general-purpose timers with 2
capture/compares
– Window-watchdog timer (WWDT)
– Independent watchdog timer (IWDT)
– RTC with alarm and calendar mode
– BEEPER generating 1/2/4/8kHz square wave to
drive an external beeper
• Communication interfaces
– Three UART modules, with one supporting LIN,
IrDA, DALI, smart card, Manchester
– Two I2C modules supporting SMBus/PMBus
and wakeup from STOP mode, supporting up
to FM+ (1Mbps)
– One SPI module supporting up to 16Mbps
• Clock system
– Internal 32MHz oscillator with -2.1% to 1.6%
accuracy (SYSOSC)
– Internal 32kHz oscillator (LFOSC) with ±3%
accuracy
– External 4MHz to 32MHz crystal oscillator
(HFXT)
– External 32kHz crystal oscillator (LFXT)
– External Low Frequency (LF) and High
Frequency (HF) digital clock inputs
– Digital clock output
• Data integrity and encryption
– Cyclic redundancy checker (CRC-16)
• Flexible I/O features
– Up to 45 total GPIOs
– Two 5V-tolerant open-drain IOs
• Development support
– 2-pin serial wire debug (SWD)
• Package options 1
– 48-pin LQFP (PT), VQFN (RGZ)
– 32-pin VQFN (RHB), VSSOP (DGS32)
– 28-pin VSSOP (DGS28)
– 24-pin VQFN (RGE)
– 20-pin WQFN (RUK), VSSOP (DGS20)
• Family members (also see Device Comparison)
– MSPM0C1106-Q1: 64KB of flash, 8KB of RAM
– MSPM0C1105-Q1: 32KB of flash, 8KB of RAM
• Development kits and software (also see Tools
and Software)
– LP-MSPM0C1106 LaunchPad™ development
kit
– MSP Software Development Kit (SDK)

2 Applications
• Automotive body electronics and Lighting
• Automotive Gateway
• Steering Wheel Systems
• Automotive Motor Control
• DC to AC Inverters
• Automotive Interior Lighting
• Door handle modules
• Kick to open modules
• Vehicle Occupancy Detection
• Seat Comfort Module

3 Description
MSPM0C1105/6 microcontrollers (MCUs) are part of MSP's highly integrated, ultra-low-power 32-bit MSPM0
MCU family based on the Arm® Cortex®-M0+ 32-bit core platform, operating at up to 32MHz frequency.
These cost-optimized MCUs offer high-performance analog peripheral integration, support extended temperature
ranges from -40°C to 125°C, and operate with supply voltages from 1.62V to 3.6V.
The MSPM0C1105/6 devices provide up to 64KB embedded flash program memory with 8KB SRAM. These
MCUs incorporate a high-speed on-chip oscillator with an accuracy from -2.1% to +1.6%, eliminating the need
for an external crystal. Additional features include a 3-channel DMA, CRC-16 accelerator, and a variety of
high-performance analog peripherals such as one 12-bit 1.6 Msps ADC with VDD as the voltage reference, a
comparator with 8-bit reference DAC and an on-chip temperature sensor. These devices also offer intelligent
digital peripherals such as one 16-bit advanced timer with deadband and timer frequency up to 64MHz, four 16-
bit general purpose timer, one windowed watchdog timer, and a variety of communication peripherals including
three UART, one SPI, and two I2C. These communication peripherals offer protocol support for LIN, IrDA, DALI,
Manchester, smart card, SMBus, and PMBus.
The TI MSPM0 family of low-power MCUs consists of devices with varying degrees of analog and digital
integration allowing for customers to find the MCU that meets the project's needs. The MSPM0 MCU platform
combines the Arm Cortex-M0+ platform with a holistic ultra-low-power system architecture, allowing system
designers to increase performance while reducing energy consumption.
MSPM0C1105/6 MCUs are supported by an extensive hardware and software ecosystem with reference designs
and code examples to get the design started quickly. Development kits include a LaunchPad available for
purchase. TI also provides a free MSP Software Development Kit (SDK), which is available as a component of
Code Composer Studio™ IDE desktop and cloud version within the TI Resource Explorer. MSPM0 MCUs are
also supported by extensive online collateral, training with MSP Academy, and online support through the TI
E2E™ support forums.