M24LR16E-R
AI

## Overview of the M24LR16E-R
The **M24LR16E-R** is a unique electronic component developed by STMicroelectronics. It is categorized as a **Dynamic NFC/RFID tag IC**. What makes it special is its **dual-interface** capability: it can be accessed via a wired connection (I2C) and a wireless connection (ISO 15693 RFID/NFC).
---
### 1. Key Technical Specifications
| Feature | Specification |
| :--- | :--- |
| **Memory Size** | 16 Kbit (2048 bytes) EEPROM |
| **Wired Interface** | I2C (Up to 400 kHz) |
| **Wireless Interface** | ISO 15693 / NFC Forum Type 5 (13.56 MHz) |
| **Supply Voltage (Vcc)** | 1.8V to 5.5V |
| **Energy Harvesting** | Analog output providing power to external circuits |
| **Data Retention** | 40 years |
| **Write Cycles** | 1,000,000 cycles |
---
### 2. Functional Electronic Blocks
The M24LR16E-R consists of several internal subsystems that allow it to bridge the gap between a microcontroller and a smartphone/RFID reader:
#### A. Dual-Interface EEPROM
The core of the chip is the non-volatile memory. Both the **I2C bus** (connected to a local MCU) and the **RF antenna** (communicating with an NFC reader) can read and write to the same memory locations.
#### B. The RF Interface (ISO 15693)
This section handles the 13.56 MHz signal from an external antenna. It includes:
* **Rectifier/Regulator:** Converts the incoming RF field into DC voltage to power the chip.
* **Demodulator:** Extracts data sent by the NFC reader.
#### C. Energy Harvesting (Vout pin)
This is a standout feature. When the chip is in a strong enough induction field (from an NFC phone or reader), it can export excess energy through a dedicated **Vout** pin to power low-power components like a low-power MCU or an LED.
#### D. The I2C Interface
Allows a standard microcontroller to interact with the memory. This interface works even when the RF field is absent, provided the chip has a Vcc supply.
---
### 3. Pin Configuration (Typical SO8/TSSOP8)
| Pin | Name | Description |
| :--- | :--- | :--- |
| 1 | **Vout** | Energy Harvesting output voltage |
| 2 | **AC0** | Antenna connection 0 |
| 3 | **AC1** | Antenna connection 1 |
| 4 | **Vss** | Ground |
| 5 | **SDA** | I2C Serial Data |
| 6 | **SCL** | I2C Serial Clock |
| 7 | **WIP/BUSY** | Write in progress or RF Busy output |
| 8 | **Vcc** | External power supply (1.8V - 5.5V) |
---
### 4. Typical Application Circuit
To use this part, you generally need a PCB-trace antenna connected to pins AC0 and AC1.
```c
// Example logic for an MCU to check if RF is busy via I2C
// Address for M24LR16E is typically 0x53 (7-bit)
void checkRFBusy() {
uint8_t status = readRegister(0x00); // Read internal control register
if (status & 0x01) {
printf("RF Interface is currently accessing memory.");
}
}
```
---
### 5. Common Use Cases
* **Zero-power Configuration:** Changing device settings via NFC while the device is still in the box (unpowered).
* **Data Logging:** An MCU writes sensor data to the EEPROM via I2C, and a user retrieves it later using a smartphone.
* **Battery-less Sensors:** Using the Energy Harvesting pin to power a small sensor only when an NFC phone is nearby.
- ⤷
How do I calculate the required antenna inductance for the M24LR16E-R?
- ⤷ What is the maximum current output of the Energy Harvesting (Vout) pin?
- ⤷ How does the password protection mechanism work for the RF and I2C interfaces?