công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

  • CFAG1602A-RNB-JP

  • AI
    The **CFAG1602A-RNB-JP** is a character Liquid Crystal Display (LCD) module manufactured by Crystalfontz. It is a highly popular display type used in embedded systems due to its reliability and standard interface. --- ## 1. Core Technical Specifications The model name itself describes the primary hardware features: | Feature | Specification | | :--- | :--- | | **Display Format** | 16 Characters x 2 Lines | | **LCD Mode** | STN Blue Negative (Blue background, white/light text) | | **Backlight** | White LED | | **Interface** | Parallel (8-bit or 4-bit) | | **Controller** | Sitronix ST7066U (or equivalent HD44780) | | **Voltage (VDD)** | 5.0V Typical | --- ## 2. Key Electronic Components ### A. The Controller (ST7066U) The "brain" of the module is the **ST7066U IC**. It is industry-standard and compatible with the Hitachi HD44780. * **Internal RAM:** Stores the character data sent by your microcontroller. * **Character Generator (CGROM):** Contains the standard font map (ASCII). * **Instruction Set:** Supports commands for clearing the screen, moving the cursor, and shifting the display. ### B. Pin Configuration (Header) The module typically uses a 16-pin interface. The electronic functions are distributed as follows: | Pin | Symbol | Function | | :--- | :--- | :--- | | 1 | VSS | Ground (0V) | | 2 | VDD | Supply Voltage (+5V) | | 3 | VO | Contrast Adjustment (via Potentiometer) | | 4 | RS | Register Select (Command vs. Data) | | 5 | R/W | Read/Write Select | | 6 | E | Enable Signal (Latch data) | | 7-14 | DB0-DB7 | Data Bus lines | | 15 | A/VEE | Backlight Anode (+) | | 16 | K | Backlight Cathode (-) | --- ## 3. Driving Considerations ### Voltage and Contrast Pin 3 (**VO**) is critical for electronics integration. You must connect a 10kΩ potentiometer between VDD and VSS, with the wiper connected to VO. This adjusts the driving voltage for the liquid crystals to ensure the text is visible. ### Backlight Circuit The white LED backlight typically requires a current-limiting resistor if the driving circuit does not provide one. Operating the backlight at 3.0V to 3.5V is standard, but check the specific forward current ($I_f$) in the datasheet to prevent burning out the LEDs. ### Logic Interfacing Since this is a **5V logic** device, if you are using a **3.3V microcontroller** (like an ESP32 or STM32), you may need: * **Level Shifters:** To step up the 3.3V signals to 5V. * **Voltage Dividers:** If reading data back from the LCD to the MCU. --- ## 4. Basic Connection Diagram (Conceptual) ```cpp // Typical Arduino Pin Mapping (LiquidCrystal Library) const int rs = 12, en = 11, d4 = 5, d5 = 4, d6 = 3, d7 = 2; LiquidCrystal lcd(rs, en, d4, d5, d6, d7); void setup() { lcd.begin(16, 2); lcd.print("CFAG1602A Test"); } ```
    ✨ Follow-up Questions
    • ⤷ How do I calculate the resistor value for the LED backlight?
    • ⤷ Can this display be modified to run on 3.3V VDD?
    • ⤷ What is the difference between 4-bit and 8-bit parallel modes for this controller?