PIC17C44-08SLASHP datasheet(180/240 Pages) MICROCHIP

180 / 240 page

PIC17C4X

DS30412C-page 180

Applicable Devices 42 R42 42A 43 R43 44

Output Low Voltage

D080

D081

VOL

I/O ports (except RA2 and RA3)

with TTL buffer

–

0.1VDD

0.1VDD *

0.4

IOL = VDD/1.250 mA

4.5V

≤ VDD ≤ 6.0V

VDD

= 2.5V

IOL = 6 mA, VDD = 4.5V

Note 6

D082

RA2 and RA3

–

3.0

IOL = 60.0 mA, VDD = 6.0V

D083

D084

OSC2/CLKOUT

(RC and EC osc modes)

–

0.4

0.1VDD *

IOL = 1 mA, VDD = 4.5V

IOL = VDD/5 mA

(PIC17LC43/LC44 only)

Output High Voltage (Note 3)

D090

D091

VOH

I/O ports (except RA2 and RA3)

with TTL buffer

0.9VDD

0.9VDD *

2.4

–

IOH = -VDD/2.500 mA

4.5V

≤ VDD ≤ 6.0V

VDD

= 2.5V

IOH = -6.0 mA, VDD=4.5V

Note 6

D092

RA2 and RA3

–

Pulled-up to externally

applied voltage

D093

D094

OSC2/CLKOUT

(RC and EC osc modes)

2.4

0.9VDD *

–

IOH = -5 mA, VDD = 4.5V

IOH = -VDD/5 mA

(PIC17LC43/LC44 only)

Capacitive Loading Specs

on Output Pins

D100

COSC2 OSC2/CLKOUT pin

–

In EC or RC osc modes

when OSC2 pin is outputting

CLKOUT.

external clock is used to

drive OSC1.

D101

CIO

All I/O pins and OSC2

(in RC mode)

–

D102

CAD

System Interface Bus

(PORTC, PORTD and PORTE)

–

In Microprocessor or

Extended Microcontroller

mode

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40˚C

≤ TA ≤ +85˚C for industrial and

0˚C

≤ TA ≤ +70˚C for commercial

Operating voltage VDD range as described in Section 19.1

Parameter

No.

Sym

Characteristic

Min

Typ†

Max

Units

Conditions

These parameters are characterized but not tested.

†

Data in “Typ” column is at 5V, 25

°C unless otherwise stated. These parameters are for design guidance only

and are not tested.

‡

These parameters are for design guidance only and are not tested, nor characterized.

Note 1: In RC oscillator conﬁguration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the

PIC17CXX devices be driven with external clock in RC mode.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The speciﬁed levels

represent normal operating conditions. Higher leakage current may be measured at different input voltages.

3: Negative current is deﬁned as coming out of the pin.

4: These speciﬁcations are for the programming of the on-chip program memory EPROM through the use of the

table write instructions. The complete programming speciﬁcations can be found in: PIC17CXX Programming

Speciﬁcations (Literature number DS30139).

5: The MCLR/VPP pin may be kept in this range at times other than programming, but is not recommended.

6: For TTL buffers, the better of the two speciﬁcations may be used.

PIC17C44-08/P bảng dữ liệu(PDF) 180 Page - Microchip Technology

PIC17C44-08/P bảng dữ liệu(HTML) 180 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL